EPCO Edge Series tab pull gives you a low-profile grip with a 2 inch center to center layout, so hole drilling is straightforward and repeatable across doors and drawers. The 4 inch overall length spans a comfortable hand area, which helps doors open smoothly on everyday use. An anodized brushed bronze finish adds a consistent metallic look, useful when matching other bronze decorative hardware on a project. The pull is back mounted, so it fastens from the inside of the panel and leaves the front face free of visible fasteners. Projection of 1-9/16 inch creates enough finger clearance while keeping the hardware tight to the edge, which supports clean, modern cabinet lines. This tab pull works on material from 1/2 inch to 7/8 inch thick, covering common cabinet door and drawer stock used in shops.
The EPCO Edge Series tab pull uses a back mounted configuration, so fastening happens from the inside of the cabinet front and leaves the outer face uninterrupted. With a 2 inch center to center hole spacing, installers can rely on simple measurements or templates to place the pull consistently. The 4 inch overall length runs along the door or drawer edge, which helps align the pull visually with the panel side. Projection of 1-9/16 inch controls how far the grip stands out, balancing knuckle clearance with tight reveals on stacked fronts. Designed for material thickness from 1/2 inch to 7/8 inch, this pull aligns with typical cabinet doors and drawer fronts, reducing the need to vary hardware for different pieces in the same run.
This EPCO Edge Series tab pull fits cabinet and drawer fronts that fall between 1/2 inch and 7/8 inch thick, which matches common plywood and solid stock used in casework. The 2 inch center to center measurement makes the pull suitable for narrower doors and drawers where compact hardware is preferred. At 4 inches overall length, the pull aligns well along the top or side edge of small to medium fronts, helping maintain proportion on modern frameless pieces or face-frame cabinets. The brushed bronze anodized finish supports use wherever a warm metallic accent is part of the design plan, from kitchen runs to shop-built storage. Because the pull is back mounted, it works especially well on clean-faced fronts where visible front fasteners would conflict with the design intent.
The 2 inch center to center dimension on this DP41-BBZ-4 tab pull standardizes drilling, which streamlines jig setup and reduces layout time across a bank of cabinets. Its 1-9/16 inch projection defines a predictable stand-off from the panel, helping maintain even clearances when doors and drawers are closely gapped. The 4 inch overall length keeps a consistent visual line along the edge, making it easier to align multiple pulls so they read as one continuous run. Working with a material range of 1/2 inch to 7/8 inch, the pull stays compatible with typical door and drawer front builds, supporting consistent hardware choice across upper, base, and utility cabinets. The anodized brushed bronze finish offers a uniform surface treatment, which helps maintain color continuity when several pulls are installed side by side.
The EPCO Edge Series tab pull uses a 2 inch center to center mounting dimension, which sets the spacing between holes and simplifies layout across multiple doors and drawers.
The EPCO Edge Series tab pull has a 4 inch overall length, giving a wider grip area along the edge of the door or drawer front for everyday cabinet use.
The anodized brushed bronze tab pull projects 1-9/16 inch from the cabinet surface, creating defined finger clearance while keeping the profile close to the panel edge.
The EPCO tab pull is back mounted, so fasteners go in from the rear of the cabinet front, leaving the exterior face free of visible fasteners.
This tab pull is designed for material thickness from 1/2 inch to 7/8 inch, covering common cabinet door and drawer front stock used in woodworking.
The DP41-BBZ-4 tab pull uses an anodized brushed bronze finish, providing a warm metallic appearance suited to bronze-themed decorative hardware projects.
Choose this EPCO Edge Series tab pull when a 2 inch center to center layout matches your drilling pattern and a 4 inch overall length suits the cabinet proportions. The 1-9/16 inch projection offers consistent clearance, which helps doors and drawers operate cleanly in tight banks. Its anodized brushed bronze finish aligns well with other bronze decorative hardware, supporting unified visual runs on projects. With a back mounted design and fit for 1/2 inch to 7/8 inch material, this pull supports straightforward installation across standard cabinet fronts.
Sold In: 1 Each