Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 4 inch tab pull provides a clean gripping point at the cabinet edge, so doors and drawers can be opened without protruding handles that interfere with adjacent fronts. The 4 inch (102 mm) center to center mounting spreads the load across two fasteners, which helps the pull stay aligned on repeated use. Its 6 inch overall length gives extra finger room beyond the fastener span, which can make it easier to grab on wider door or drawer edges. The anodized satin bronze finish creates a uniform surface that resists surface wear, helping the pull maintain a consistent appearance during everyday cabinet operation. As a tab-style pull, it mounts at the edge rather than the face, which supports a minimalist layout while still giving a defined pull point. This configuration suits installers and woodworkers planning contemporary cabinet runs.
The EPCO DP41-BZ-6 tab pull is back mounted, so fasteners pass through the cabinet material from the rear into the pull body, creating a secure connection without visible heads on the front. It is specified for material thickness of 1/2 inch to 7/8 inch, meaning it is designed to grip properly on common cabinet door and drawer stock in that range. Within this thickness range, the pull can sit correctly on the edge while the fasteners gain sufficient purchase, supporting repeatable installation results. The 4 inch center to center dimension provides a clear drilling reference, which helps maintain uniform alignment across multiple fronts. Its 1-9/16 inch projection defines how far the pull extends from the edge, which can be factored into door spacing and overlay planning.
This EPCO Edge Series 4 inch tab pull is part of the Decorative Hardware & Moldings handles and pulls category, so it is intended to act as the gripping point on cabinet doors and drawers. The design mounts at the edge, placing the pull where fingers naturally reach along the door or drawer perimeter. With 6 inch overall length and 1-9/16 inch projection, the pull provides a defined area to grab, which can help users open and close fronts with a consistent motion. The center to center 4 inch mounting dimension places the fasteners inside that grip span, so the pull remains stable under hand force. Anodized satin bronze finish gives the aluminum pull a bronze-tone surface, which visually coordinates with other bronze-hued decorative hardware in the same space.
The 4 inch center to center measurement on this EPCO DP41-BZ-6 tab pull provides an exact drilling pattern, which supports straight rows of pulls across long cabinet runs and helps keep reveals visually even. Because it is designed for material thickness from 1/2 inch to 7/8 inch, the pull engages well with typical cabinet doors and drawer fronts, helping the clamping force distribute correctly without overhanging a thin edge or floating on a thick one. Its back mounted configuration means the exterior face of the pull remains uninterrupted, which can speed wiping during routine cleaning because there are no exposed fastener heads to work around. The 1-9/16 inch projection sets a consistent stand-off from the cabinet edge, which can be considered when pairing this pull with neighboring hardware or adjacent cabinets to maintain comfortable finger clearance between surfaces.
The EPCO DP41-BZ-6 tab pull has a 4 inch center to center mounting, 6 inch overall length, and 1-9/16 inch projection, so installers can plan drilling and clearances around those fixed dimensions.
The EPCO Edge Series tab pull is back mounted, meaning fasteners go through the door or drawer from the rear into the pull, leaving the front surface free of visible fastener heads.
The EPCO DP41-BZ-6 is specified for material thickness of 1/2 inch to 7/8 inch, so it is suited to common cabinet door and drawer stock within that range.
This EPCO Edge Series 4 inch tab pull has an anodized satin bronze finish, giving the aluminum a controlled bronze-tone surface for coordinated decorative hardware layouts.
The 4 inch center to center spacing matches a common mounting span, allowing drilling templates and repeated measurements to be standardized across multiple cabinet fronts.
This EPCO decorative cabinet pull has a 1-9/16 inch projection, setting the pull out from the cabinet edge to give finger clearance while doors and drawers are operated.
The EPCO Edge Series 4 inch tab pull, model DP41-BZ-6, combines a 4 inch center to center pattern, 6 inch overall length, and 1-9/16 inch projection in an anodized satin bronze finish, which supports coordinated cabinet runs. For projects using 1/2 inch to 7/8 inch thick doors or drawers, this back mounted pull offers a defined edge grip and a drilling pattern that can be repeated across the job. Add this tab pull to the layout when an anodized satin bronze, edge-mounted gripping point aligns with the cabinet design.
Sold In: 1 Each