Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 1 inch tab pull gives you a compact back mounted grip at a 1 inch center to center size, so you can line up handles tightly on small doors or drawer fronts while keeping a consistent hardware layout across a run. The 1-1/2 inch overall length keeps the pull footprint short, which helps when working on narrow rails or tight cabinetry where space for hardware is limited. Its 1-9/16 inch projection provides enough clearance for fingers to grab from the edge, improving day to day usability without extending far off the front. The pull is designed for material thickness of 1/2 to 7/8 inch, so it covers common cabinet stock ranges and supports uniform use across mixed panel builds. The charcoal metallic finish delivers a modern, low-profile look that ties in with contemporary decorative hardware.
This back mounted cabinet tab pull installs through the rear of the material, so the body clamps against the panel for a secure grip on doors and drawer fronts. Its 1 inch center to center drilling dimension defines the hole pattern, which guides accurate spacing when you are laying out multiple pulls in a straight line. With an overall length of 1-1/2 inch, the handle suits short edges where a full-length pull would crowd nearby hardware or trim. The 1-9/16 inch projection sets the stand off from the face, creating enough room for fingers behind the lip while limiting snag points in walk-by areas. Rated for material thickness of 1/2 to 7/8 inch, this tab pull adapts across many cabinet side and front thicknesses within a typical woodworking shop.
The EPCO Edge Series 1 inch tab pull fits doors and drawer fronts built from 1/2 to 7/8 inch thick material, so it works across many cabinet carcass and front constructions that use these stock ranges. Its 1 inch center to center measurement suits smaller drawers or narrow upper doors where full-size handles might dominate the front. The 1-1/2 inch overall length helps the pull sit tight to the corner of the panel, which is useful on compact fronts such as vanity drawers or small wall cabinets. A 1-9/16 inch projection gives enough offset from the face for fingers to pull comfortably, especially when mounted at the top edge of a door or drawer. The charcoal metallic finish makes this decorative hardware a fit wherever a darker metallic tone is part of the design palette.
The defined 1 inch center to center dimension on this EPCO DP41-CM tab pull makes drill layout predictable, so jigs or templates can be reused across an entire run for consistent placement. Its back mounted configuration means the pull is anchored through the panel, which helps maintain alignment over time because the fasteners work in shear across the material thickness. By keeping overall length to 1-1/2 inch, the handle reduces interference with adjacent hardware on tight spacing, so rows of pulls can repeat at closer intervals on multi-drawer stacks. The 1-9/16 inch projection provides a standard pull-off distance from the cabinet face, which supports a uniform grab feel from one door or drawer to the next. Matching the product by EPCO brand and DP41-CM part number helps maintain the same geometry whenever additional decorative handles are added later.
The EPCO DP41-CM pull has a 1 inch center to center, 1-1/2 inch overall length, and 1-9/16 inch projection, which defines drilling layout and how far it stands off the cabinet face.
This tab pull is designed for material thickness of 1/2 to 7/8 inch, so it works across common cabinet door and drawer front stock used in many woodworking projects.
The EPCO Edge Series DP41-CM is a back mounted pull, so it fastens from the rear of the panel and leaves a clean appearance on the front face of the cabinet.
The 1 inch center to center dimension defines the distance between mounting points, guiding hole drilling and helping align this pull consistently across multiple doors or drawers.
The 1-9/16 inch projection sets how far the pull extends from the surface, giving finger clearance for an easy grip while keeping the profile compact on cabinet faces.
The charcoal metallic finish gives the tab pull a modern dark metal look, helping it coordinate with contemporary decorative hardware and other charcoal-toned handles.
The EPCO Edge Series 1 inch tab pull in charcoal metallic brings defined dimensions and back mounted construction to small cabinet doors and drawers. With its 1 inch center to center drilling, 1-1/2 inch overall length, and 1-9/16 inch projection, it supports precise layout and a comfortable grip across 1/2 to 7/8 inch material. Choose the DP41-CM part when you want a compact decorative handle that keeps lines clean while matching other charcoal metallic hardware across your installation.
Sold In: 1 Each