Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series aluminum tab pull gives a compact 1 inch center to center grip that works well where a small, consistent hand hold is needed across doors or drawers. The 1-1/2 inch overall length keeps the hardware footprint tight, which helps on narrow faces or tight layouts where larger pulls crowd each other. Its 1-9/16 inch projection brings the grip out from the door edge, giving fingers room to catch the pull without dragging across the surface. The back mounted design fastens from the inside face, leaving the front edge clean, which suits jobs that call for a simple, uninterrupted look. Aluminum construction keeps weight down while providing a solid metal feel at the door or drawer edge. The DP41-M part number identifies this specific Edge Series pattern, helping maintain the same look and dimensions across a run of cabinets.
This back mounted aluminum tab pull uses the 1 inch center to center spacing as the key drilling reference, so once that spacing is set on a template, each door or drawer front can be processed the same way. Its 1-1/2 inch overall length allows placement near the edge without overhanging neighboring fronts, which helps on tight reveals. The 1-9/16 inch projection works with the back mount approach to bring a comfortable grip away from the panel while still tying firmly into the door or drawer from behind.
The 1 inch center to center layout positions this EPCO Edge Series aluminum tab pull well on small to medium cabinet doors and drawers where hardware needs to stay compact. Its 1-1/2 inch overall length fits cleanly at edges, which is useful on modern frameless cabinetry or tight drawer stacks where long pulls are impractical. The 1-9/16 inch projection supports a usable grip at the door or drawer edge, so fronts can operate smoothly without needing oversized handles. Back mounted construction suits cabinets where the front edge must remain visually simple, because the fasteners are concealed on the interior side. Aluminum construction keeps each pull light on the door edge, which is helpful when working with multiple pulls on the same panel.
The fixed 1 inch center to center dimension on the DP41-M aluminum edge pull allows installers to use a single drilling pattern across an entire job, limiting layout variability and rework. Its 1-1/2 inch overall length defines a small, repeatable footprint, which makes it straightforward to align pulls at equal setbacks from corners or edges. The 1-9/16 inch projection creates a predictable standoff from the cabinet face, so doors and drawers open with the same feel from one front to the next. Back mounted fastening lets installers work from the inside face, which supports accurate pull placement by referencing interior layout lines. The EPCO DP41-M designation keeps ordering and replacement simple on future phases or service calls that require matching the original Edge Series hardware.
The EPCO DP41-M aluminum edge pull uses a 1 inch center to center hole spacing, which sets a consistent layout point for drilling and aligning multiple pulls on a project.
The EPCO Edge Series aluminum tab pull has a 1-9/16 inch projection, bringing the grip off the face enough for fingers to catch comfortably at the door or drawer edge.
The DP41-M tab pull has an overall length of 1-1/2 inches, giving a compact footprint that works well on smaller fronts and tight cabinet layouts.
The EPCO Edge Series aluminum tab pull is back mounted, so it fastens from the rear face of the door or drawer and leaves the front edge visually clean.
The DP41-M tab pull is specified for material thickness of 1/2 inch to 7/8 inch, matching many common cabinet door and drawer front constructions.
The EPCO Edge Series DP41-M pull is made from mill aluminum, providing a straightforward metal finish that pairs with a wide range of cabinet styles.
The EPCO Edge Series aluminum tab pull with 1 inch center to center drilling, 1-1/2 inch overall length, and 1-9/16 inch projection offers a compact, repeatable hardware choice. For cabinets using 1/2 inch to 7/8 inch thick fronts, this back mounted DP41-M profile supports a clean edge line while giving a consistent grip feel across doors and drawers.
Sold In: 1 Each