Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO edge series tab pull gives a low-profile way to open cabinet doors and drawers while staying clear of the front face. The 2 inch center to center drilling sets consistent spacing between fasteners, which helps layout work across multiple fronts. The 3 inch overall length provides a compact grip area that suits narrow doors or drawer fronts without crowding neighboring hardware. Its 1-9/16 inch projection creates enough space to grab the pull comfortably while keeping it close to the panel edge for a streamlined look. Back mounted design lets the pull fasten from the rear of the door or drawer, which hides fastener heads on the working face and keeps the installation looking tidy. Aluminum construction keeps the pull lightweight, which reduces load on smaller doors and helps hardware operate smoothly over time.
The back mounted layout of this EPCO aluminum edge pull means holes are drilled from the rear and the pull nests over the panel edge, which creates a clean front face while giving solid mechanical attachment. The 2 inch center to center dimension defines the distance between the mounting points, which guides drilling locators when setting up jigs or templates for repeat installs. Material thickness suitability from 1/2 inch to 7/8 inch matches typical cabinet door and drawer front stock, which lets the same setup carry across multiple box types. Its 1-9/16 inch projection sets the stand-off from the face, which keeps fingers clear of the edge while avoiding interference with adjacent doors or hardware in tight banks of cabinets.
The DP41-M-3 is a center to center 2 inch tab pull with a 3 inch overall length, which suits doors and drawer fronts where a compact grip is preferred over full-width handles. Its fit range for 1/2 inch to 7/8 inch material aligns with many frameless and face-frame cabinet designs, which supports use on both wall and base units built from standard sheet goods. The aluminum construction keeps the hardware light on the door edge, which works well on smaller or thinner fronts that do not need heavy pulls. With a back mounted configuration, the pull seats over the top or side edge and secures from behind, which lets designers keep the visible face clear while still adding practical access.
The fixed 2 inch center to center spacing on this EPCO edge series tab pull simplifies repetitive layout across a shop run, which helps drilling jigs stay consistent and reduces alignment adjustments between cabinets. Its 3 inch overall length provides a known reference distance along the panel edge, which can be used to line up multiple pulls to trim pieces or rail joints for a uniform look. The 1-9/16 inch projection defines how far the pull stands out from the face, which helps plan clearances between parallel doors or drawers and can reduce handle-to-handle clashes. Compatibility with 1/2 inch to 7/8 inch thick material gives a clear envelope for door and drawer design, which supports predictable seating of the pull on typical cabinet stock. The aluminum build keeps the component easy to handle during installation, which can help maintain accuracy when working at finished fronts.
The EPCO edge series tab pull has a 2 inch center to center dimension, a 3 inch overall length, and a 1-9/16 inch projection, which together define drilling, grip area, and stand-off from the cabinet face.
The EPCO edge series tab pull fastens from the rear of the door or drawer, so the pull seats over the edge while fasteners tighten from the back, leaving the front face clear of visible fastener heads.
The DP41-M-3 edge pull is specified for material thickness from 1/2 inch to 7/8 inch, which matches many cabinet doors and drawer fronts made from common sheet stock.
A 2 inch center to center tab pull provides a compact mounting spread, which helps on smaller fronts and supports easy jigging when repeating the same drilling pattern across multiple cabinets.
The 1-9/16 inch projection holds the pull away from the cabinet face enough for a comfortable grip while keeping hardware close to the edge, which supports a streamlined profile in tight runs.
The aluminum construction keeps the EPCO edge series tab pull lightweight, which reduces added load on doors and pairs well with lighter cabinet fronts in typical woodworking projects.
The EPCO edge series tab pull with 2 inch center to center spacing and 3 inch overall length offers a defined pattern that suits repeat cabinet runs and tight layouts. Its back mounted installation and 1-9/16 inch projection create a discreet profile with practical grip. Fit for 1/2 inch to 7/8 inch material, it aligns with common cabinet door and drawer front thicknesses used in many shops. For projects calling for a compact, aluminum edge pull, this DP41-M-3 model from Wurth Baer Supply supports straightforward layout and clean finished results.
Sold In: 1 Each