Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull delivers a compact, back mounted grip that keeps cabinet faces clear while still giving a solid handhold. The 1 inch center to center mounting sets a tight screw pattern, which works well on smaller doors and drawer fronts where space is limited. The 1-1/2 inch overall length keeps the pull discreet, so it fits tight layouts without crowding adjacent fronts. An anodized oil rubbed bronze finish provides a consistent, dark appearance across pulls, helping banks of cabinets read as a planned set. This pull is designed for edge-style mounting, which lets it wrap the top or side of a front instead of sitting on the face, useful when a minimal look is desired. As part of the EPCO Edge Series in decorative hardware and moldings handles and pulls, it aligns visually across a full run of cabinetry.
This EPCO aluminum edge pull is back mounted, so it fastens through the rear of the door or drawer front, leaving the working face clean. A 1 inch center to center layout sets the hole pattern, which guides drilling when lining up multiple pulls in a row. The pull is specified for material thickness from 1/2 inch to 7/8 inch, meaning it is intended to sit correctly on common cabinet door and drawer stock without awkward overhang. A 1-9/16 inch projection positions the gripping surface away from the front, giving fingers clearance even when the cabinet front thickness varies within that stated range. Being part of the handles and pulls category under decorative hardware and moldings, it is suited to cabinetry where a slim edge grip is preferred over bulkier handle styles.
The 1 inch center to center anodized oil rubbed bronze tab pull format works well on cabinet doors and drawers that benefit from a linear, understated grip at the edge. With an overall length of 1-1/2 inches, this EPCO Edge Series tab pull fits neatly on narrow rails and stiles, allowing multiple fronts to open from a consistent top or side edge line. The projection of 1-9/16 inches means the pull stands off the front enough for a comfortable grasp when mounted on fronts within the 1/2 inch to 7/8 inch material thickness range, which corresponds to many standard cabinet constructions. An anodized oil rubbed bronze finish allows this aluminum edge pull to visually coordinate with other oil rubbed bronze cabinet hardware, supporting a uniform color story across a kitchen, bath, or casework project. As a decorative hardware and moldings handle and pull, it helps create a continuous, modern edge detail without drawing attention away from door and drawer faces.
The back mounted design of this aluminum edge pull directs all fastening from the interior side of the cabinet front, which can streamline installation when fronts are drilled from the back using a jig aligned to the 1 inch center to center spacing. This fixed spacing provides a clear reference dimension, reducing layout variation between doors and drawers on longer runs. The specified fit for material thickness from 1/2 inch to 7/8 inch indicates the tab is proportioned to sit properly on typical cabinet stock, supporting an even reveal at the edge and a repeatable feel from one front to the next. With a 1-1/2 inch overall length, the DP41-ORB tab pull reduces the chance of conflict at corners or between closely spaced fronts, while the 1-9/16 inch projection gives fingers consistent clearance on all matching cabinets in the project. The EPCO brand and the DP41-ORB identifier tie this edge pull to a specific pattern and finish, which helps maintain exact matching across replacements or extensions of an existing installation.
The EPCO Edge Series tab pull has a 1 inch center to center mounting, a 1-1/2 inch overall length, and a 1-9/16 inch projection, giving a compact footprint with generous finger clearance.
The EPCO aluminum edge pull uses back mounted fastening, so screws are driven from the rear of the front, leaving the cabinet face free of visible fastener heads.
The EPCO Edge Series tab pull is specified for material thickness from 1/2 inch to 7/8 inch, aligning with many standard cabinet door and drawer front constructions.
The DP41-ORB aluminum edge pull has an anodized oil rubbed bronze finish, providing a consistent dark tone that coordinates with other oil rubbed bronze cabinet hardware.
The 1 inch center to center spacing on this EPCO tab pull offers a simple, repeatable drilling pattern, which supports consistent alignment across multiple doors and drawers.
The EPCO DP41-ORB part number identifies this specific Edge Series aluminum tab pull size and anodized oil rubbed bronze finish, aiding accurate matching and reordering.
The EPCO aluminum edge pull in anodized oil rubbed bronze pairs a 1 inch center to center mounting with a 1-1/2 inch overall length, giving a compact, predictable footprint on cabinet fronts. Its 1-9/16 inch projection and fit range from 1/2 inch to 7/8 inch material thickness support comfortable operation on common cabinet builds. With the DP41-ORB designation and EPCO branding, it provides a defined pattern that can be repeated across projects requiring a back mounted, edge-style tab pull.
Sold In: 1 Each