EPCO Edge Series tab pull gives you a low-profile way to open cabinet doors and drawers while keeping front faces clear. The 2 inch center to center layout concentrates the grip area in a compact span, which helps when you are aligning multiple pulls in a tight run. With a 4 inch overall length, the pull extends beyond the screw spacing to give fingers a stable edge, useful on both small doors and narrower drawer fronts. A 1-9/16 inch projection sets the working distance off the edge, providing enough space to grab while still staying close to the cabinet for a streamlined look. The anodized oil rubbed bronze finish establishes a consistent color tone across the pull, helping it blend with other bronze hardware in the same area. The EPCO brand and DP41-ORB-4 part number identify this pull within a coordinated Edge Series.
This EPCO Edge Series tab pull is back mounted, so it fastens from the rear of the cabinet component and clamps over the edge. That layout suits frameless and face-frame cabinetry where you want an edge-grip opening point instead of a front-mounted handle. The pull is specified for material thickness of 1/2 inch to 7/8 inch, defining the range of door or drawer stock it will seat on without overhanging or sitting loose. Center to center spacing of 2 inches sets the drilling pattern, which can speed layout when repeating across multiple doors. With 1-9/16 inch projection, the pull establishes a predictable offset from the cabinet surface, helping you maintain consistent reveals and avoid interference with adjacent doors.
The EPCO Edge Series tab pull with 4 inch overall length works well anywhere an edge-grip opening point is preferred over a projecting handle. The 2 inch center to center spacing concentrates the fasteners near the edge, which is useful on thinner rails or compact drawer fronts where there is limited drilling space. Because the pull is designed for material thickness from 1/2 inch to 7/8 inch, it suits common cabinet door and drawer stock in that range, letting you apply the same hardware across much of a project. The back mounted configuration leaves the front surface free of screw heads, supporting a cleaner appearance on contemporary or transitional cabinets. Its anodized oil rubbed bronze finish coordinates with other bronze-toned pieces, helping maintain visual continuity from base cabinets to wall units.
The 2 inch center to center dimension on this DP41-ORB-4 tab pull provides a fixed drilling template that can be repeated across doors and drawers, promoting consistent alignment from one opening to the next. A 4 inch overall length gives a stable reference when positioning the pull along the edge, so installers can align by measuring from corners or finished ends. The specified 1-9/16 inch projection defines how far the pull stands off the surface, which helps prevent interference when doors swing past adjacent fronts or when drawers operate close to neighboring cabinets. Suitability for 1/2 inch to 7/8 inch material thickness means the same part can be used on a range of panel constructions within that band, reducing part variation on site. The anodized oil rubbed bronze finish provides a defined surface layer that supports a uniform look, aiding in matching multiple pulls during replacements or additions over time.
The EPCO Edge Series tab pull has 2 inch center to center screw spacing, a 4 inch overall length, and 1-9/16 inch projection, giving a compact footprint with practical finger clearance.
The back mounted configuration seats the pull over the edge and fastens from the rear, leaving the front face without exposed fastener heads for a cleaner look.
This EPCO tab pull is specified for material thickness of 1/2 inch to 7/8 inch, covering common cabinet door and drawer stock within that range.
The pull has an anodized oil rubbed bronze finish, providing a consistent bronze tone that coordinates with similar decorative hardware.
The 1-9/16 inch projection sets a defined stand-off from the cabinet surface, giving enough space for fingers while keeping the profile close to the edge.
DP41-ORB-4 identifies this specific EPCO Edge Series 4 inch tab pull in anodized oil rubbed bronze, simplifying selection and matching across a project.
The EPCO Edge Series tab pull in anodized oil rubbed bronze combines a 2 inch center to center pattern, 4 inch overall length, and 1-9/16 inch projection to support clean, repeatable cabinet layouts. Its back mounted design and suitability for 1/2 inch to 7/8 inch material thickness allow use across many doors and drawers in the same project. With the DP41-ORB-4 designation, it aligns with EPCO decorative hardware and moldings, giving you a defined option when standardizing tab pulls across new installations or updates.
Sold In: 1 Each