Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO edge series tab pull gives you a compact 1 inch center to center grip that works well where a small, consistent handle layout is needed across doors and drawers. The 1-1/2 inch overall length keeps the pull tight to the edge, which helps maintain a clean, modern cabinet face while still giving enough tab to grab. Its 1-9/16 inch projection creates finger space off the door or drawer front, so you can open panels without knuckles riding the surface. Back mounting design lets the pull fasten from the rear of the material, leaving the front side free of visible fasteners for a simple look. Being part of EPCO decorative handles and pulls means it fits standard cabinet hardware expectations for professional shops and serious DIY projects.
This back mounted aluminum cabinet pull is built for a 1 inch center to center spacing, so drilling is straightforward when laying out multiple pulls on a run of fronts. The 1-1/2 inch overall length means the mounting points stay close to the door or drawer edge, which is useful when working with narrow rails or compact drawer heads. With a projection of 1-9/16 inch, the tab stands proud enough to grip while remaining tight to the cabinetry line. The pull is specified for material thickness from 1/2 to 7/8 inch, which lines up with many common cabinet doors, drawer fronts, and panels in shop and site work. Anodized polished aluminum construction provides a smooth, finished surface that pairs well with modern casework and decorative hardware layouts.
This EPCO edge series tab pull is part of the decorative handles and pulls category, so it suits cabinet, drawer, and similar casework applications where a low-profile grip is preferred. The 1 inch center to center layout makes it practical on smaller fronts, such as narrow drawers or compact doors, where larger pulls would visually dominate the panel. At 1-1/2 inch overall length, the pull stays close to the edge, working well on frameless cabinetry or face-frame rails that do not allow deep hardware. A projection of 1-9/16 inch gives enough depth to grasp the pull without contacting the door surface, which is valuable on high-use fronts. The design for material thickness between 1/2 and 7/8 inch aligns with many shop-built doors and fronts, supporting use across multiple cabinet lines in the same workspace.
The fixed 1 inch center to center dimension helps create repeatable drilling patterns, so jigs and templates can be reused across a job for consistent placement. Keeping the overall length at 1-1/2 inch minimizes variation between the edge of the front and the pull, which supports a uniform reveal when aligning hardware along a bank of doors or drawers. The 1-9/16 inch projection establishes a predictable standoff from the face, useful when coordinating with adjacent components such as doors that swing past each other or drawers under overhanging tops. Back mounted construction means layout is handled from the rear side of the panel, which can simplify marking and drilling on unfinished or less visible surfaces during fabrication. The anodized polished aluminum finish delivers a consistent appearance across multiple pulls, supporting jobs that require a unified hardware look.
The EPCO DP41-PA is an edge series anodized polished aluminum tab pull, so it provides a small grip at the door or drawer edge for modern cabinet installations.
This tab pull has a 1 inch center to center dimension, which sets a compact hole layout useful for narrow fronts and tight hardware spacing.
The EPCO edge series tab pull is 1-1/2 inch overall length, keeping it compact for smaller doors and drawer fronts while still offering a usable grip.
The projection is 1-9/16 inch, giving enough stand-off from the cabinet face for fingers to grab without scraping the surface during use.
This EPCO tab pull is back mounted, so it fastens from the rear of the material, leaving the front face clear of visible fasteners.
This pull is designed for material thickness from 1/2 to 7/8 inch, matching many standard cabinet doors and drawer fronts in shop-built casework.
The EPCO edge series tab pull with 1 inch center to center spacing lets you plan tight, repeatable hardware rows across cabinets and drawers. Its 1-1/2 inch overall length and 1-9/16 inch projection balance a compact footprint with everyday grip comfort. Back mounted installation keeps front faces clean while you work from the rear of the panel. With design coverage for 1/2 to 7/8 inch material thickness, this anodized polished aluminum pull aligns with a wide range of cabinet constructions. Put it into your next layout when you want consistent, small-format pulls that match modern decorative hardware projects.
Sold In: 1 Each