Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull is a back mounted handle that grips the top or edge of the door or drawer, giving a streamlined option for cabinets where a low-profile pull is preferred. The 2 inch center to center mounting spreads the load between two fasteners, which helps the pull sit solidly on the edge and keeps alignment consistent across multiple fronts. The 3 inch overall length gives enough finger contact along the edge without crowding smaller doors or narrow drawer faces. Its 1-9/16 inch projection sets the pull out from the surface, creating room for fingers to grab the edge comfortably during regular use. Being part of the Handles and Pulls decorative hardware category, this piece fits jobs where the pull needs to function as both working hardware and visible trim. The EPCO brand identity helps match this pull to other EPCO decorative hardware on the same project.
This EPCO Edge Series tab pull is back mounted, so it fastens from the rear of the door or drawer front and leaves only the slim tab visible on the working face. The pull is designed for material thickness from 1/2 inch to 7/8 inch, which covers common cabinet door and drawer front builds in many shop standards. Within that thickness range, the grip area and projection stay consistent, which helps doors in a run operate with the same feel. The 2 inch center to center dimension lets installers use standard drilling patterns, which supports efficient installation on both new cabinet builds and hardware change-outs that are laid out to that spacing.
This EPCO Edge Series tab pull sits in the Decorative Hardware & Moldings Handles and Pulls category, so it is intended for visible cabinet locations where the pull becomes part of the finished look. The anodized polished aluminum finish gives a bright, metallic appearance that pairs with aluminum framing, modern laminate fronts, or other aluminum pulls on the same job. Its 3 inch overall length and 2 inch center to center spacing make it well suited to standard residential or commercial cabinet doors and drawer fronts where a compact pull is preferred. Because it mounts on material from 1/2 inch to 7/8 inch thick, it works across many cabinet construction methods, from thinner slab fronts to heavier door designs, as long as they fall within that stated range.
The 1-9/16 inch projection on this tab pull sets how far the gripping edge stands off the face, which affects hand clearance and the feel of opening motions. With this defined projection, installers can line up multiple pulls and expect the same finger clearance across a run of doors, which supports a uniform user experience. The back mounted design hides the fasteners from the front, giving a clean visual line and reducing visual clutter on flat cabinet fronts. The 2 inch center to center dimension works as a fixed drilling reference, which means jigs or templates can be used to repeat the hole pattern, reducing layout time and keeping pulls level relative to each other. The defined material thickness range of 1/2 inch to 7/8 inch ties directly to how the pull seats over the edge; within this band, the pull can sit properly on the edge while the mounting points engage the back side of the door or drawer. The EPCO DP41-PA-3 manufacturer part number also matters in a shop setting, because it lets project documents, cut lists, and ordering systems call out this exact pull and avoid mismatched hardware on later reorders.
The EPCO Edge Series tab pull has a 2 inch center to center dimension, which sets the drilling distance between mounting points for consistent layout across cabinets.
The DP41-PA-3 edge pull is 3 inches overall length, so it fits comfortably on smaller fronts and narrow rails while still giving a usable gripping area.
This anodized polished aluminum tab pull projects 1-9/16 inches, giving finger clearance between the pull and the cabinet surface during regular opening and closing.
The EPCO Edge Series tab pull is back mounted, so it fastens from the rear of the door or drawer and leaves only the tab visible from the front.
This edge pull is designed for material thickness from 1/2 inch to 7/8 inch, covering many common cabinet door and drawer front constructions.
The DP41-PA-3 pull is made from anodized polished aluminum, providing a bright metallic appearance that coordinates with other aluminum cabinet hardware.
The EPCO Edge Series tab pull with 2 inch center to center spacing, 3 inch overall length, and 1-9/16 inch projection offers a defined set of dimensions that fit many cabinet runs using 1/2 inch to 7/8 inch material. Its back mounted design and anodized polished aluminum construction give a clean, modern look that can align with other decorative handles and pulls on the project. Using the DP41-PA-3 part number ties this specific pull into ordering and shop documentation, helping keep hardware consistent from one phase of work to the next.
Sold In: 1 Each