EPCO Edge Series tab pull gives a low-profile way to open cabinet fronts while keeping a simple line across the door or drawer. This anodized polished brass pull uses a 2 inch center to center layout, so installers get a compact grip that fits small to medium cabinet widths without crowding other hardware. The 3 inch overall length keeps the pull visually tight to the door edge, which matters where multiple fronts sit close together on built-ins or banks of drawers. A 1-9/16 inch projection creates enough finger clearance to grab the pull comfortably, reducing fumbling on heavier doors. The back mounted design leaves the front face free of visible fasteners, helping maintain a clean, finished appearance on modern or traditional cabinetry. EPCO branding and the DP41-PB-3 designation tie this pull to a defined decorative hardware and moldings line for consistent project selection.
This EPCO Edge Series tab pull is back mounted, so fasteners enter from the rear of the cabinet material into the pull body, helping lock the pull to the edge while keeping the working face clear. The design is specified for material thickness of 1/2 to 7/8 inch, giving installers a defined range of door and drawer front builds that match the pull geometry. When fronts fall inside that 1/2 to 7/8 inch span, the grip area and projection remain consistent, which supports uniform feel across a full installation. The 2 inch center to center dimension works as the drilling reference, so layout can be transferred directly from plans or templates without guesswork. Combined with the 3 inch overall length, the pull anchors near the edge while still delivering the full 1-9/16 inch projection for hand access.
This EPCO Edge Series tab pull sits within the decorative hardware and moldings handles and pulls category, aligning it with cabinet and furniture applications where a slim edge grip is preferred. The back mounted style suits doors and drawers built from 1/2 to 7/8 inch material, which covers common cabinet construction thicknesses in many woodworking projects. With a 2 inch center to center spacing and 3 inch overall length, the pull fits along door and drawer edges without dominating the panel, supporting layouts with multiple pulls across stacked drawers. The anodized polished brass finish brings a defined brass tone for projects that call for warm metallic accents. Because the projection is set at 1-9/16 inch, the pull extends enough to catch fingers along the edge, helping users open fronts smoothly while the pull remains visually compact.
The defined 2 inch center to center measurement gives installers a reliable drilling dimension, so once the first pull is laid out, the rest can follow the same spacing for consistent alignment. The 3 inch overall length lines the pull closely along the edge, which simplifies positioning in relation to the corner of the door or drawer front. Specifying the pull for 1/2 to 7/8 inch material thickness means that within this range, the engagement and feel of the pull remain similar from cabinet to cabinet. The 1-9/16 inch projection provides a fixed stand-off from the surface, which helps maintain uniform clearance where doors meet adjacent panels or appliances. An anodized polished brass finish defines both color and surface treatment, so planners can repeat the same visual across added sections or later phases of a job using the DP41-PB-3 part number.
The EPCO Edge Series tab pull has a 2 inch center to center spacing, a 3 inch overall length, and a 1-9/16 inch projection, giving installers fixed reference points for layout and hand clearance.
The back mounted EPCO tab pull fastens from the rear of the material, so no fasteners show on the front face, which keeps cabinet fronts visually clean.
The DP41-PB-3 tab pull is specified for material thickness of 1/2 to 7/8 inch, aligning with many cabinet door and drawer front constructions.
The EPCO Edge Series tab pull has an anodized polished brass finish, giving a defined brass color and sheen for coordinating decorative hardware.
The 1-9/16 inch projection sets the pull out from the surface, providing consistent finger clearance when gripping doors and drawers along the edge.
The DP41-PB-3 part number identifies this specific EPCO Edge Series anodized polished brass tab pull configuration for ordering and matching across projects.
The EPCO Edge Series tab pull with 2 inch center to center spacing, 3 inch overall length, and 1-9/16 inch projection offers a defined set of dimensions for consistent cabinet layouts. Its anodized polished brass finish and back mounted design support clean, coordinated fronts across doors and drawers. For projects using 1/2 to 7/8 inch material, this DP41-PB-3 pull keeps edge access comfortable while maintaining a compact footprint. Apply these fixed measurements across your run to streamline drilling patterns, visual alignment, and future matching when extending existing installations.
Sold In: 1 Each