Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives you a 2 inch center to center grip in a compact format that keeps cabinet faces clear, which helps maintain straight visual lines on doors and drawers. The 4 inch overall length spreads hand force over a slightly wider area, which supports confident opening on small to medium fronts. An anodized polished brass finish provides a bright metal surface, which suits decorative hardware jobs that call for a brass look. The tab pull is back mounted, so it fastens from the rear of the door or drawer and leaves the front face uncluttered. A projection of 1-9/16 inch creates finger space behind the pull, which helps when grabbing from above or below. The pull is designed for material thickness from 1/2 to 7/8 inch, which matches common cabinet door and drawer front stock.
The back mounted EPCO Edge Series tab pull uses 2 inch center to center screw spacing, which simplifies jig setup because two straight holes control both position and alignment. Its 4 inch overall length positions the gripping edge beyond the door or drawer edge, which allows fingers to hook the pull without modifying the cabinet profile. A 1-9/16 inch projection offers clearance between the pull and surface, which helps when users approach from the side on base cabinets. The specified 1/2 to 7/8 inch material thickness range defines where the pull seats correctly, which keeps the tab section tight to the edge for a solid feel. #6 x 1/2 inch screws match a common cabinet fastener length, which suits typical door and drawer front build-ups.
The EPCO Edge Series tab pull with 4 inch overall length suits cabinet fronts where a slim edge grip is preferred, which keeps hardware from projecting far into walkways or tight galley layouts. Its 2 inch center to center drilling pattern fits small to mid-sized doors and drawers, which supports consistent spacing on upper and base cabinets. The back mounted configuration places all fastening from the inside face, which is useful on finished exterior faces that need uninterrupted polished brass appearance. Support for 1/2 to 7/8 inch material thickness lets this pull serve on typical slab doors, drawer fronts, and applied panels, which helps keep hardware uniform across mixed cabinet constructions in a single room.
The 2 inch center to center dimension on the DP41-PB-4 provides a fixed reference that aligns with many drilling templates, which cuts layout time when installing multiple pulls on site or in the shop. Its 1-9/16 inch projection gives a repeatable stand-off from the cabinet face, which produces the same hand clearance at every opening and keeps edges from feeling cramped. The anodized polished brass finish delivers a stable surface treatment, which supports a consistent look across pulls even when installed at different times during a project. Using #6 x 1/2 inch screws standardizes the fastener interface, which streamlines tooling and helps maintain consistent bite in common cabinet materials along an entire run of doors and drawers.
The EPCO Edge Series tab pull has a 2 inch center to center measurement, which sets the hole spacing and helps align drilling jigs and templates for repeat cabinet layouts.
The DP41-PB-4 tab pull has a 4 inch overall length, which provides a compact grip area that works well on smaller doors and drawer fronts without crowding adjacent fronts.
This EPCO Edge Series tab pull projects 1-9/16 inch from the cabinet surface, which creates finger clearance behind the pull for comfortable opening from different angles.
The tab pull is back mounted, so screws install from the rear of the door or drawer, which leaves the front face free of exposed fastener heads during and after installation.
This EPCO pull is designed for material thickness from 1/2 to 7/8 inch, which covers common cabinet doors, drawer fronts, and panels used in typical woodworking projects.
The DP41-PB-4 pull uses #6 x 1/2 inch screws, which match a common cabinet fastener size and support secure mounting into standard door and drawer substrates.
The anodized polished brass EPCO Edge Series tab pull with 2 inch center to center spacing ties together decorative hardware on doors and drawers, which supports a coordinated brass look across a project. Its 4 inch overall length and 1-9/16 inch projection offer a compact yet usable grip, which suits tight runs and smaller fronts. With a back mounted layout sized for 1/2 to 7/8 inch material and #6 x 1/2 inch screws, this DP41-PB-4 pull integrates smoothly into standard cabinet construction, ready to be applied wherever an edge-style brass pull is needed.
Sold In: 1 Each