Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives a low-profile grip along the cabinet edge, so doors and drawers open by catching the pull at the top instead of adding bulky fronts. The 4 inch (102 mm) center to center dimension sets consistent drill spacing, which helps line up multiple pulls across a run of doors. A 6 inch overall length extends beyond the mounting points, giving extra finger room at the edge while still keeping the hardware compact. The anodized polished brass finish provides a bright metallic look on aluminum, so you get a brass appearance with an aluminum base. Back mounting keeps fasteners inside the door or drawer, leaving only the tab visible on the exterior surface. Designed as a tab pull, it suits modern and minimalist cabinet layouts where a thin edge grip is preferred.
This EPCO Edge Series tab pull is described for material thickness of 1/2 inch to 7/8 inch, so it is sized for common cabinet door and drawer stock within that range. Back mounted construction means the pull is fastened from the rear face, which keeps the working steps on the inside of the component during installation. The 4 inch center to center specification provides the reference for drilling or boring through the material, letting installers align holes precisely to the pull body. With a 1-9/16 inch projection, the pull extends enough from the edge to allow fingers behind the tab while keeping the front layout tight. The 6 inch overall length gives a clear visual cue along the edge of the door or drawer, aiding consistent positioning during layout.
The EPCO Edge Series tab pull is specified for material thickness of 1/2 inch to 7/8 inch, so it aligns with many cabinet doors and drawer fronts made from common panel stock in that thickness band. Back mounting at the edge places the pull so that the working grip is along the top or side, which suits layouts where the hardware is meant to disappear into the line of the cabinet. The 4 inch center to center spacing provides the structural anchor points in that edge zone, so drilling passes straight through the material and into the pull body on the back. Because the overall length is 6 inches, there is visible hardware beyond the hole centers, giving users a defined place to grab without filling the whole drawer front. The anodized polished brass finish sets a brass-colored appearance that can coordinate with other brass-toned decorative hardware and moldings in the same area.
The anodized polished brass tab pull has a 1-9/16 inch projection, which describes how far the grip stands off the face of the door or drawer to create working clearance. That projection allows fingers to hook behind the edge without requiring a deep handle, useful on cabinets installed near adjacent surfaces. The 6 inch overall length combined with the 4 inch center to center dimension defines the geometry of the pull, so installers can plan edge spacing, alignment to panel width, and sequencing of multiple pulls across a bank of drawers. As an EPCO decorative hardware part in the Handles and Pulls class, this DP41-PB-6 edge pull fits into hardware schedules that call out specific part numbers for repeatable results. On a project where the same center to center distance is repeated, this defined layout reduces layout variation from cabinet to cabinet.
The DP41-PB-6 is an EPCO Edge Series anodized polished brass tab pull, which mounts along the cabinet edge so users pull from a thin grip instead of a full handle bar.
This tab pull uses a 4 inch center to center mounting dimension with a 6 inch overall length, so drilling and layout follow a 4 inch hole spacing while the visible pull extends to 6 inches.
The EPCO Edge Series tab pull has a 1-9/16 inch projection, giving room for fingers behind the tab while keeping the hardware close to the cabinet face.
This tab pull is back mounted, so it attaches from the inside face of the door or drawer and presents only the edge tab on the exterior side.
This EPCO tab pull is specified for material thickness of 1/2 inch to 7/8 inch, matching many cabinet doors and drawer fronts in common panel sizes.
The DP41-PB-6 cabinet pull has an anodized polished brass finish, giving the aluminum pull a bright brass-colored appearance suited to brass-toned hardware schemes.
The EPCO Edge Series tab pull with 4 inch center to center spacing and 6 inch overall length offers a clear pattern for repetitive cabinet runs. With its anodized polished brass finish, 1-9/16 inch projection, and back mounted design for 1/2 inch to 7/8 inch material, it provides a specific, repeatable solution when a slim edge pull is required. Use the DP41-PB-6 identifier when specifying or ordering so this exact anodized polished brass edge tab pull is used consistently across the project.
Sold In: 1 Each