EPCO Edge Series 2 inch tab pull gives a compact grip point with a 2 inch center to center hole spacing, so it fits small cabinet doors and drawers where tight layouts limit handle options. The 3 inch overall length provides a bit of overhang past the fasteners, creating a defined finger grab without taking over the door face. An anodized stainless steel finish on the aluminum body delivers a stainless look surface that resists everyday handling wear in cabinet use. Back mounted installation keeps all fastening points on the inside of the door or drawer front, leaving a clean outside appearance for modern projects. The 1-9/16 inch projection sets the pull away from the edge, offering finger room while keeping fronts from catching loose clothing in tight walkways. Designed as a tab pull, it works well wherever a low profile cabinet handle is needed.
The 2 inch center to center drilling on this EPCO tab pull lets installers align to standard two-hole patterns, which speeds layout on repeat cabinet runs and simplifies replacements on small fronts. With a 3 inch overall length, the pull lands neatly on narrow doors and drawers, so corners, end panels, and small vanity fronts still gain a usable handhold. The specified 1/2 to 7/8 inch material thickness range means typical cabinet doors and drawer faces accept the back mounted fasteners without odd gaps. A 1-9/16 inch projection establishes a predictable standoff from the front, which helps keep lines straight when multiple pulls run across banks of cabinets. Back mounting keeps hardware heads inside the cabinet, supporting a tidy exterior face that suits modern residential or commercial projects using this EPCO Edge Series part.
The EPCO Edge Series 2 inch center to center tab pull works on cabinet doors and drawers built with 1/2 to 7/8 inch thick material, so it suits many face-frame and frameless cabinet fronts. Its 3 inch overall length is sized for smaller doors, narrow drawer fronts, and compact bath or office cabinets where longer pulls might crowd neighboring hardware. The 1-9/16 inch projection holds the gripping edge off the surface, letting fingers catch the tab easily on doors near walls or adjacent appliances. With an anodized stainless steel finish on an aluminum pull, it visually coordinates with stainless-style fixtures and appliances on kitchen, break room, or storage cabinets. The back mounted format supports use on clean-faced panels, because the outer side shows only the tab profile rather than visible screw heads.
The 2 inch center to center spacing on the DP41-SS-3 tab pull provides a fixed drilling reference, making it straightforward to set jigs or templates so every pull lines up across a run of doors. Its 3 inch overall length creates a defined edge-to-edge footprint, helping installers repeat the same setback from corners for a consistent visual line. The 1-9/16 inch projection keeps the grip height uniform, which matters when coordinating with adjacent appliances or nearby hardware depths. Because the pull is specified for 1/2 to 7/8 inch material thickness, installers can rely on a predictable fit on many stock cabinet components without altering the door build. The anodized stainless steel finish gives a stable surface that maintains a similar appearance from pull to pull, which supports a finished look when using multiple DP41-SS-3 handles in one installation.
The EPCO Edge Series 2 inch tab pull uses a 2 inch center to center hole spacing, so holes are drilled 2 inches apart to match the mounting posts on cabinet doors or drawers.
The DP41-SS-3 tab pull has a 3 inch overall length, giving a compact profile that works well on smaller cabinet doors and drawer fronts where space is limited.
The EPCO Edge Series pull projects 1-9/16 inch from the mounting surface, creating room behind the tab so fingers can grip the cabinet edge comfortably when opening.
The tab pull is designed for cabinet material thickness from 1/2 to 7/8 inch, matching many standard door and drawer front constructions used in cabinetry.
The DP41-SS-3 pull has an anodized stainless steel finish on its aluminum body, providing a stainless-style appearance suited to modern cabinet layouts.
This EPCO Edge Series pull is back mounted, so it attaches from the interior side of the cabinet front, leaving a smooth exterior face with just the tab visible.
The EPCO Edge Series 2 inch tab pull brings together 2 inch center to center drilling, a 3 inch overall length, and 1-9/16 inch projection to suit compact cabinet fronts. Its anodized stainless steel finish and back mounted design support clean, modern cabinet runs using 1/2 to 7/8 inch thick doors or drawers. For projects using EPCO decorative hardware and moldings, this DP41-SS-3 handle offers a defined tab profile that fits tight spaces while keeping alignment straightforward across multiple fronts.
Sold In: 1 Each