Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives you a low-profile way to operate doors and drawers while keeping flat fronts clear. The anodized stainless steel construction provides a consistent look across projects where stainless appearance is required. With a 4 inch center to center dimension, this pull aligns with common drilling patterns used in cabinet and millwork shops. The 6 inch overall length offers a balanced grip area along the edge of doors or drawer fronts. A 1-9/16 inch projection creates enough clearance to grab without sticking far off the surface, which helps when working tight clearances between fronts. Back mounted design allows you to fasten from the inside face of the material so the front shows only the clean tab profile, which suits modern and minimalist layouts in kitchens, baths, and casework.
The EPCO Edge Series tab pull is back mounted, so it installs from the rear of the door or drawer front for a streamlined face. A 4 inch center to center hole spacing sets the drilling pattern, guiding layout on jigs and line-boring equipment. With an overall length of 6 inches, the pull positions along the edge to give adequate grip without dominating narrower fronts. The 1-9/16 inch projection defines how far the pull sits off the surface, affecting clearances to adjacent cabinets or walls. Designed for material thickness from 1/2 inch to 7/8 inch, this pull works across a range of common cabinet constructions such as slab fronts and applied panels.
This EPCO Edge Series tab pull fits cabinet and millwork applications calling for an edge-mounted grip with a modern profile. The 4 inch center to center dimension suits many kitchen, bath, and built-in cabinet layouts that already follow this drilling standard. Its 6 inch overall length lets you position the tab along door or drawer edges so users can easily hook fingers from above or below. The specified 1/2 inch to 7/8 inch material thickness range aligns with typical door and drawer front builds in plywood, MDF, or solid fronts, so a single pull model can serve multiple box lines. Because it is back mounted, it works well on fronts where a clean exterior surface is part of the design intent.
The defined 4 inch center to center spacing helps maintain consistent handle alignment across a run of cabinets, which is important when doors and drawers line up tightly. The 6 inch overall length gives a fixed reference for positioning the tab relative to the top or side edge, simplifying jigs for repetitive setups. The 1-9/16 inch projection is known in advance, so you can plan reveals between fronts and adjacent panels to preserve finger access without interferences. Specifying use on 1/2 inch to 7/8 inch material thickness provides a clear range for door and drawer front selection, helping keep hardware behavior consistent from unit to unit. The anodized stainless steel finish establishes a uniform visual standard, so multiple pulls installed across a project present a coordinated appearance.
The DP41-SS-6 pull has a 4 inch center to center measurement, 6 inch overall length, and 1-9/16 inch projection, so layout and clearances can be planned precisely.
The EPCO Edge Series tab pull mounts from the back of the material, leaving the exterior face with a clean tab profile and concealed fastener heads.
This EPCO Edge Series tab pull is specified for material from 1/2 inch to 7/8 inch thick, covering many common cabinet door and drawer front constructions.
The 1-9/16 inch projection provides reliable finger clearance for gripping the pull while keeping it relatively low profile on cabinet faces.
The 4 inch center to center spacing matches a widely used drilling pattern, so it supports consistent layout on new cabinets using standard boring setups.
The DP41-SS-6 tab pull is anodized stainless steel, providing a stainless appearance that coordinates with other stainless-look decorative hardware.
The EPCO Edge Series tab pull DP41-SS-6 combines a 4 inch center to center layout with 6 inch overall length for straightforward cabinet runs. Its anodized stainless steel finish and back mounted design support clean, modern fronts on doors and drawers. With a defined 1-9/16 inch projection and a 1/2 inch to 7/8 inch material thickness range, this pull fits many standard cabinet constructions and clearances. For projects calling for an edge-style grip on contemporary casework, this tab pull matches common drilling setups and finish expectations.
Sold In: 1 Each