Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives you a compact handle option with a 2 inch center to center layout, so hole drilling aligns with common small-door and drawer spacing while keeping the pull footprint tight and controlled. The 4 inch overall length provides enough finger contact along the edge for everyday opening without taking over the cabinet face. A 1-9/16 inch projection sets the pull out at a practical distance, giving good finger clearance while staying close to the door for a low-profile look. Back mounted construction fastens from the inside of the door or drawer, leaving the exterior surface free of visible fasteners for a clean installation line. The pull is designed for material thickness from 1/2 to 7/8 inch, covering typical cabinet door and drawer fronts so one model works across a run of casework.
This EPCO pull uses a 2 inch center to center drilling pattern, so installers can base jigs and templates on a simple two-hole layout that repeats cleanly across doors and drawers. The back mounted design relies on interior access for fastening, which suits cabinet doors and drawer fronts where the back side is open during assembly. With a projection of 1-9/16 inch from the mounting surface, the pull sets up a predictable standoff that helps coordinate with nearby doors, drawer faces, and adjacent hardware. The pull fits material thickness from 1/2 to 7/8 inch, aligning with many standard cabinet constructions so one drilling and mounting approach works across a full installation.
This EPCO Edge Series tab pull is part of the decorative hardware and moldings category, placing it within common cabinet handles and pulls used on doors and drawers. The 4 inch overall length works well along the edge of both narrow and medium-width fronts, giving enough pull surface at the corner without reaching too far into the panel. Its center to center dimension of 2 inch suits smaller doors, vanity fronts, and compact drawers where a short drilling span is preferred. Material thickness coverage from 1/2 to 7/8 inch means installers can apply it on many residential and commercial cabinet fronts within that range, from thinner stock panels to slightly heavier doors. The gloss white powdercoat finish presents a bright white look that coordinates with white or light-colored casework, so banks of cabinets can carry a uniform pull style.
The 2 inch center to center drilling point allows installers to set up a consistent drilling template, improving repeatability when running multiple doors and drawers on site or in the shop. With a 1-9/16 inch projection, the pull offers steady finger clearance from the surface, which helps users get a reliable grip even on heavier fronts while keeping the profile compact. Back mounted construction places fasteners on the interior side, supporting an uninterrupted exterior edge and reducing visual distraction along minimal cabinet designs. The ability to work on material from 1/2 to 7/8 inch thickness gives flexibility when projects mix different panel build-ups, since the same pull style can carry across those fronts. As part of EPCO decorative hardware, this handle and pull format integrates into standard cabinet hardware layouts where tab pulls are preferred at the door or drawer edge.
The EPCO Edge Series tab pull has a 2 inch center to center dimension, which sets the drilling distance between mounting holes for consistent layout on doors and drawers.
The DP41-WH-4 pull has a 4 inch overall length, giving enough edge length for a secure grip while keeping the hardware compact on smaller cabinet fronts.
This EPCO tab pull projects 1-9/16 inch from the mounting surface, creating practical finger clearance while keeping the handle close to the cabinet face.
The EPCO Edge Series pull is back mounted, so it fastens from the interior side of the door or drawer, leaving the exterior edge free of visible fastener heads.
This tab pull is designed for material thickness from 1/2 to 7/8 inch, covering many common cabinet door and drawer front constructions.
The EPCO Edge Series DP41-WH-4 uses a gloss white powdercoat finish, providing a smooth white appearance that pairs with light-colored casework.
The EPCO Edge Series tab pull with 2 inch center to center spacing, 4 inch overall length, and 1-9/16 inch projection offers a defined layout for doors and drawers. With back mounted construction and fit for 1/2 to 7/8 inch material, it suits many cabinet fronts using a consistent drilling pattern. The gloss white powdercoat finish supports coordinated white or light cabinet runs. Select the DP41-WH-4 edge pull when this mix of dimensions, mounting method, and finish aligns with your cabinet hardware plan.
Sold In: 1 Each