Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 72 inch aluminum tab pull defines this handle as a long, continuous pull suited to runs up to 6 feet, so one part can span tall cabinet doors or wide panels without breaking the line with multiple shorter pulls. The SAP description states this is an unfinished aluminum pull, so the surface arrives in a basic aluminum state that can be integrated into projects that call for that look or prepared according to shop standards before final installation. The web description specifies a length of 6 feet, so layout on full-height cabinetry, tall closets, or long drawers can be planned around a single, consistent gripping edge. With a stated width of 2 inches, the pull presents a broad tab profile, giving fabricators a defined metal edge to reference when aligning to door or drawer fronts during assembly. The web description also lists this product in the Handles and Pulls class from EPCO, so it serves as a functional grip in decorative hardware layouts across residential or commercial woodworking work.
The web description lists this EPCO aluminum tab pull as top mounting, so the working edge is designed to sit along the top of a cabinet door or drawer front, creating a continuous grip line that follows the upper edge. Because the SAP description notes there are no holes and no screws, the bar arrives as a solid length that shops can drill or machine to their own layout, tying hole spacing directly to the cabinet construction and internal framing. With its 6 foot length and 2 inch width, the pull provides ample material for installers to position it to balance user reach, clearance to adjacent fronts, and any overlay scheme already defined in the project. As a member of EPCO Handles and Pulls, this part fits into hardware schedules where metal pulls are specified as the primary operating points on millwork and cabinetry.
The product name identifies this handle as an EPCO Edge Series 72 inch length aluminum tab pull, so it is suited to straight runs where a linear grip is required along the edge of a cabinet component. The 6 foot length from the web description lets fabricators apply the pull across full-height pantry or wardrobe doors without piecing together shorter sections, helping maintain a single visual line from top to bottom. The 2 inch width noted in the SAP description means the metal edge projects enough to serve as a defined grasp point along the top of doors or wide drawers, which supports everyday cabinet operation in kitchens, closets, or built-in storage. Being part of the Handles and Pulls product class from EPCO, this tab pull integrates into decorative hardware plans that specify metal pulls as both functional and visual elements in the woodworking package.
The SAP description explicitly states this aluminum pull has no holes and no screws, so fabricators control every drilled location, aligning fixing points with stile locations, internal rails, or reinforcement in the cabinet design. This flexibility means the same DP42-L-M bar can be adapted across different cabinet lines where hole patterns change, without being locked into preset mounting points. The web description confirms top mounting, so the installer positions the pull along the top edge of the front, which helps maintain consistent reveals because the working hardware is referenced to a single, repeatable edge. With a 6 foot length and 2 inch width, there is enough material to trim or position within a run if a particular project calls for the pull to start or stop at specific heights, giving shops room to fine-tune alignment in the field or in the shop.
The EPCO DP42-L-M pull has a length of 72 inches, described as 6 feet, so it can span tall doors or wide fronts with a single continuous handle run.
The SAP description lists a 2 inch width, so the pull presents a substantial tab edge that provides a defined grip and a clear reference band on the cabinet face.
The web description notes top mounting, so the pull is oriented along the top edge of doors or drawers to form a continuous upper grip.
The SAP description specifies no holes, so the pull is supplied as a solid aluminum length that shops can drill according to their preferred layout.
The SAP description calls it an unfinished aluminum pull, so the surface is provided in a basic aluminum state appropriate for aluminum-focused projects.
The web description notes it is packed and sold in each, so project takeoffs can be counted per individual 6 foot pull length.
The EPCO Edge Series 72 inch aluminum tab pull DP42-L-M offers a 6 foot, 2 inch wide, top mounting handle that suits tall doors and wide fronts where a single continuous grip is preferred. Its unfinished aluminum construction and absence of holes described in the SAP entry give fabricators control over surface prep and drilling patterns, so the same part can align with different cabinet lines and hole schemes. For projects routed through Wurth Baer Supply that call for a long, edge-mounted aluminum handle from EPCO, this pull provides a defined hardware choice that can be integrated directly into hardware schedules and shop drawings.
Sold In: 1 Each