Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 72 tab pull is a 72 inch (1829 mm) anodized satin clear aluminum pull that creates a continuous gripping edge along doors or drawer fronts. The 6 foot length lets you run one uninterrupted pull across tall doors or a bank of drawers, which helps keep lines straight and consistent on larger cabinet runs. This tab pull is part of EPCO decorative handles and pulls, so it is built for visible applications where hardware layout matters on finished work. The aluminum construction keeps weight down on moving fronts while still providing a defined edge to grab. Because this piece is a dedicated pull profile, it gives a predictable gripping surface wherever it is installed.
This EPCO DP43-L-A tab pull is back mounted, so it engages from the rear of the door or drawer front while the pull lip is exposed at the edge. The pull is designed for material thickness from 1/2 inch to 7/8 inch, which covers common cabinet stock so one profile can handle typical kitchen, bath, or casework panels within that range. The 72 inch (1829 mm) length gives room to position the pull along the full edge and trim as the installation plan requires, which aids in aligning pulls across adjacent fronts. Because it is an anodized satin clear aluminum piece, it remains light enough to handle in long lengths during fitting and layout.
This anodized satin clear aluminum tab pull fits projects using material from 1/2 inch to 7/8 inch thick, so it suits many cabinet doors and drawer fronts built from standard sheet goods in that range. The 72 inch (1829 mm) length supports runs on tall pantry doors, wardrobe fronts, or wide drawer banks where a continuous gripping edge is preferred. Because this pull is part of the EPCO Edge Series, it is intended for edge-mounted applications where the hardware becomes a linear detail along the panel. The neutral satin clear finish lets it sit against light or dark fronts without changing the basic profile, which helps when one job mixes colors but uses a single pull style. Sold in each units, it can be applied wherever a continuous tab pull is called for across multiple openings.
The back mounted design means the installer works from the rear of the panel, so the visible face stays focused on the slim pull edge without extra visible fastener points around it. This matters on modern or flush cabinetry where straight lines and uninterrupted faces are part of the design intent. The defined material range of 1/2 inch to 7/8 inch gives a clear window for panel selection, which supports predictable fit of the pull profile along the edge and helps keep the gripping lip consistent from door to door. At 72 inches (1829 mm), the pull can be cut down when the layout needs shorter segments, so one stock length serves various opening sizes on the same project. Being an aluminum tab pull keeps the long profile relatively light during cutting and handling, which helps when aligning several pieces along a run. The EPCO DP43-L-A part number clearly identifies this exact Edge Series configuration when matching project specs or reordering for future work.
The EPCO DP43-L-A is an Edge Series anodized satin clear aluminum tab pull, so it creates a slim gripping edge along cabinet doors or drawers while keeping a low-profile look.
The EPCO Edge Series DP43-L-A tab pull is 72 inches, or 1829 mm, long, which suits tall cabinet doors or long drawer runs that benefit from a continuous pull edge.
The EPCO DP43-L-A tab pull fits material from 1/2 inch to 7/8 inch thick, covering many common cabinet doors and drawer fronts built from standard sheet stock.
The EPCO Edge Series DP43-L-A tab pull is back mounted, so it attaches from the rear of the panel while the pull lip remains at the front edge for gripping.
The EPCO DP43-L-A tab pull has an anodized satin clear aluminum finish, giving a neutral metallic appearance that works with many cabinet colors and styles.
The EPCO DP43-L-A tab pull is packing and sold in each units, so it can be ordered in exact quantities that match the specific number of openings on a project.
The EPCO Edge Series 72 tab pull combines a 72 inch anodized satin clear aluminum profile with back mounted installation and fit for 1/2 inch to 7/8 inch material, aligning well with many cabinet layouts. For jobs needing a continuous, low-profile gripping edge across tall doors or drawer banks, this EPCO DP43-L-A configuration offers a defined size, finish, and mounting style that can be matched directly to project drawings. When a project calls for a linear tab pull solution, this 6 foot length provides a single, consistent profile to work into your next cabinet or casework run.
Sold In: 1 Each