Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO 72 inch aluminum pull provides a continuous 6 foot gripping edge, so one part can span wide drawers or cabinet fronts without breaking the line of the run. The aluminum construction gives a stable, rigid pulling surface that stands up to frequent use on regularly accessed fronts. This DP46-2-L-M model is designed as a decorative handle and pull, so it finishes off millwork while also serving as the working grip point. With a 72 inch or 1829 mm length, it suits tall pantry fronts or banks of drawers cut from a single face, helping maintain a consistent look across the full width. The pull stays as one straight piece, which reduces layout decisions around joints when planning long runs in the shop.
This EPCO 72 inch aluminum pull is specified for flush mortise mounting, so the profile is set into a machined recess rather than sitting proud on the surface. That mounting style lets the front remain largely flush while still giving a defined gripping edge along the mortised line. The pull is listed for any material thickness of 13/16 inch, which means the geometry is matched to that stock dimension for practical cabinet work. Using a pull sized for 13/16 inch material helps keep the mortise depth and front thickness in balance, supporting consistent joinery and edge strength across a run of fronts.
The DP46-2-L-M aluminum drawer pull is suited to cabinet and drawer fronts built from 13/16 inch material, so it aligns with common casework and kitchen millwork thicknesses. At 72 inches or 1829 mm long, it works on wide base drawers, tall pantry fronts, or multi-drawer arrays where a single continuous pull is preferred over several short handles. As decorative hardware within the handles and pulls category, it ties into broader trim and molding designs, allowing the pull line to coordinate with other aluminum elements in the installation. The flush mortise mounting keeps the face profile clean, which is useful on modern fronts where a recessed grip is preferred over projecting hardware.
The flush mortise mounting design of this EPCO 72 inch aluminum pull lets the body sit within a routed recess, so only the working edge defines the grip line, reducing snag points on the face. Because the pull is specified for any material thickness of 13/16 inch, the installer can cut mortises knowing the pull depth is suited to that stock, which supports consistent shoulder lines and edge integrity along the full 6 foot span. The continuous aluminum profile distributes hand force along the length, which helps large drawers or tall fronts feel more controlled when opened from different positions. With a defined manufacturer part number DP46-2-L-M, this pull can be called out precisely on plans, aiding coordination between design, shop cutting lists, and field installation so the mortised fronts match the exact pull profile.
The DP46-2-L-M aluminum drawer pull has a 72 inch or 1829 mm overall length, so it can span wide cabinet or drawer fronts with a single continuous gripping edge.
The EPCO 72 inch aluminum pull is designed for flush mortise mounting, so it sets into a machined recess in the front, leaving a clean, recessed grip line across the face.
The DP46-2-L-M pull is specified for any material thickness of 13/16 inch, aligning the pull geometry with common cabinet stock used in drawers and doors.
This 6 foot EPCO aluminum pull suits wide drawers, tall pantry fronts, or aligned drawer banks where a single, continuous handle is preferred across the entire width.
As decorative hardware in the handles and pulls class, this aluminum pull provides both a working grip and a continuous visual line along cabinet or drawer fronts.
This EPCO aluminum drawer pull is identified by manufacturer part number DP46-2-L-M, which provides a clear reference for specifying and ordering through Wurth Baer Supply.
The EPCO 72 inch aluminum pull DP46-2-L-M offers a 6 foot continuous grip sized for 13/16 inch material, so it fits common cabinet stock while supporting flush mortise mounting. For wide drawers or tall fronts where a single aluminum handle line is desired, this pull gives a defined, recessed grip that aligns with decorative hardware and moldings work. Specify DP46-2-L-M when a continuous aluminum pull is needed across a long cabinet or drawer run.
Sold In: 1 Each