Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO 72 inch anodized polished aluminum pull describes a 72 inch long handle that spans 1829 mm, so it can run nearly the full width of large drawer fronts or panels in one continuous piece. The anodized polished aluminum finish gives the pull a bright metal appearance, which presents a clean, modern edge on casework where the handle is part of the design. This pull is identified as POL ALUM DRAWER PULL,NO HOLES/SCRWS,6FTL, so the bar arrives without pre-drilled mounting points, allowing layout to match custom drawer widths or hole spacing. The Web Description states Length: 6', confirming the bar length matches common 6 foot stock sizing. The handle is listed under Decorative Hardware & Moldings in Handles and Pulls, so it fits directly into cabinetry and millwork projects that call for a continuous linear pull detail.
The Web Description states Flush mortise mounting, which means this EPCO pull is intended to sit into a mortised groove so its profile finishes flush to the surface, allowing drawer fronts or panels to present a low-profile grip line. The same description notes it is for any material thickness of 13/16 inch, so cabinetmakers can size drawer boxes and fronts around this known thickness, simplifying standardization of parts. Because it is a drawer pull with no holes/no screws mentioned in the SAP description, installers can mill mortises and add fastening methods according to their preferred shop process while maintaining the flush fit and edge alignment.
This EPCO DP46-2-L-PA pull is categorized as Decorative Hardware & Moldings under Handles and Pulls, so it is aimed at cabinetry, furniture, and millwork where a long, continuous handle line is desired. The 72 inch (1829 mm) length allows one pull to serve wide drawer banks or tall cabinet panels, reducing breaks in the handle line across a run. Its suitability for any material thickness of 13/16 inch means it pairs naturally with casework built from common 3/4 inch stock, giving a predictable relationship between panel thickness and the pull profile. Because the SAP Description states POL ALUM DRAWER PULL,NO HOLES/SCRWS,6FTL, shops can treat the part as a blank extrusion for layouts that match their own drilling patterns or design standards without being locked into fixed hole locations.
The flush mortise mounting described in the Web Description gives installers a clear installation method that helps achieve a level, repeatable reveal along drawer edges or cabinet faces. Mortising the 72 inch anodized polished aluminum pull into 13/16 inch thick material helps create a consistent front surface, which supports clean alignment across multiple drawers in a stack. The anodized polished aluminum finish keeps the visible edge uniform along the full 6 foot length, so any bank of drawers using this pull reads as a single visual band. The handle being identified by manufacturer part DP46-2-L-PA provides a precise reference for reordering, so repeat projects or later additions can match existing installations by part number and description.
The EPCO DP46-2-L-PA pull has a 72 inch, or 1829 mm, length, so it can span a full 6 foot drawer front or cabinet panel in one continuous piece.
The pull uses flush mortise mounting, so it is set into a mortised groove, allowing the exposed edge to finish nearly level with the drawer or panel face.
The Web Description notes this pull is for any material thickness of 13/16 inch, giving a defined panel thickness for planning drawer fronts or cabinet doors.
The SAP Description identifies it as a POL ALUM DRAWER PULL, indicating an anodized polished aluminum finish that presents a bright metal edge on casework.
The pull is listed under Decorative Hardware & Moldings in Handles and Pulls, placing it in the primary hardware group used for drawers and cabinet fronts.
The SAP Description states NO HOLES/SCRWS, so shops can establish their own drilling patterns and fastening approach to suit specific drawer layouts and design standards.
The EPCO 72 inch anodized polished aluminum pull DP46-2-L-PA provides a 6 foot, 1829 mm long handle designed for flush mortise mounting in 13/16 inch thick material, making it suited to wide drawer fronts and continuous cabinet runs. Its classification as a POL ALUM DRAWER PULL,NO HOLES/SCRWS,6FTL gives fabricators an un-drilled length of decorative hardware that can be machined to their own patterns while keeping a consistent polished aluminum appearance across the project.
Sold In: 1 Each