EPCO 3 inch center to center pull positions the mounting holes exactly 3 inches apart, which sets a consistent hand-grab point across multiple doors and drawers. The overall length of 3-7/8 inches gives you a bit more bar to grab than the hole spacing alone, which helps fingers clear the door surface during regular use. This pull is made from aluminum, so it adds a rigid, lightweight handle that does not load up door weight. The anodized satin clear finish provides a uniform look across the pull surface, which supports clean visual lines on finished cabinetry. The pull is designed for material thickness of 13/16 inch, which aligns the grip correctly on typical cabinet doors and drawer fronts. Flush mortise mounting seats the pull into a cutout, so the front face lies level with the surface for a streamlined feel along a run of cabinets.
The DP46-A aluminum cabinet pull uses flush mortise mounting, so the body of the pull drops into a routed recess and sits level with the surrounding surface. This arrangement keeps projections down along door and drawer faces, which is useful on cabinets where a low-profile front is important. With center to center at 3 inches, the drilled holes anchor the pull in a standard spread, which simplifies using templates or jigs during layout. The design for material thickness of 13/16 inch positions the pull correctly on that stock, which helps maintain alignment on face-frame or panel runs built to that dimension. Combined with the 3-7/8 inch overall length, the pull gives a comfortable gripping span while still fitting compact cabinet fronts without crowding.
This EPCO 3 inch center to center pull fits doors and drawer fronts drilled at a 3 inch spread, which is common on many cabinet layouts. The 3-7/8 inch overall length keeps the pull sized for standard cabinet modules, so it works well on kitchen, bath, or shop storage built around similar front proportions. Aluminum construction keeps the pull light on the door edge, which is useful when hardware weight needs to stay modest on smaller fronts. The pull is designed for material thickness of 13/16 inch, so it suits fronts built from that stock where the goal is a consistent handle position relative to the panel face. With flush mortise mounting, the pull sits into the surface, which matches applications that call for a streamlined, low-profile grip along continuous runs of cabinetry.
The 3 inch center to center dimension on this DP46-A aluminum cabinet pull establishes a fixed drilling pattern, which lets installers use the same jig across multiple fronts without layout changes. This steady hole spacing reduces layout variability, which helps doors and drawers line up visually when viewed down a cabinet bank. The 3-7/8 inch overall length allows extra bar beyond the mounting points, which gives more room for fingers and keeps the contact area centered, reducing uneven wear at the ends. Design for 13/16 inch material thickness standardizes how far the pull sits from edges on that stock, which helps keep rows of pulls at a uniform distance across similar components. Flush mortise mounting positions the pull in a routed pocket, which helps the handle resist rotation and keeps the visible face tight to the panel for a clean finished line.
This EPCO aluminum pull has a 3 inch center to center spacing, which sets the hole distance for drilling and matches layouts built around that standard spread.
The DP46-A pull has an overall length of 3-7/8 inches, which offers a slightly longer gripping surface than the 3 inch hole spacing for easier hand placement.
This anodized satin clear aluminum pull is designed for material thickness of 13/16 inch, which positions the handle appropriately on fronts built from that stock.
The DP46-A aluminum cabinet pull uses flush mortise mounting, so it sits into a recess and leaves the pull face level with the surrounding cabinet surface.
The EPCO DP46-A pull has an anodized satin clear aluminum finish, which provides a uniform surface appearance across the visible handle area.
This EPCO aluminum pull is offered by Wurth Baer Supply, a distributor focused on products for the woodworking and cabinet industries.
The anodized satin clear aluminum DP46-A handle from EPCO ties together 3 inch center to center spacing, 3-7/8 inch overall length, and design for 13/16 inch material thickness in a single pull, which targets cabinet fronts built to those dimensions. Flush mortise mounting lets the pull sit into the workpiece, which suits projects calling for a low-profile grip along aligned doors and drawers. For runs based around a 3 inch spread and 13/16 inch stock, this aluminum pull keeps hardware choice consistent with the layout.
Sold In: 1 Each