EPCO edge pull gives you a low-profile way to add a grasp point on doors or drawers while keeping faces uninterrupted. This EPCO Edge Series pull is an anodized satin clear aluminum handle, so it provides a neutral metallic look that works with a wide range of cabinet finishes. The pull has a 1-1/4 inch (32 mm) center to center dimension, which sets the mounting hole spacing for precise drilling and repeatable layouts across multiple fronts. Overall length is 50 mm, so the pull stays compact at the door edge while still offering enough length for a comfortable finger grip. The part is designed for back mounted installation, which keeps fasteners hidden from the front and supports a clean, modern appearance on finished cabinetry. EPCO branding and the DP47-A part number give you a specific component to match on future jobs.
This EPCO DP47-A edge pull is designed as a back mounted component, meaning it anchors from the rear of the cabinet door or drawer front. The 1-1/4 inch (32 mm) center to center dimension establishes the distance between mounting points, guiding bit spacing for drilling. Overall length of 50 mm keeps the pull located close to the edge, which helps align the grip area with the door or drawer reveal. The design for material thickness of 1/2 inch to 7/8 inch defines the range of panel stock that accepts this pull, covering common cabinet construction thicknesses. The anodized satin clear aluminum finish stays consistent across the exposed edge, which supports clean alignment when multiple pulls are installed in a row.
This EPCO Edge Series DP47-A pull fits cabinet work that uses door and drawer fronts within the 1/2 inch to 7/8 inch material range, matching the specified thickness design. The 1-1/4 inch (32 mm) center to center dimension lines up well with compact doors, narrow drawer fronts, and smaller panels where a short mounting spread is appropriate. Its 50 mm overall length keeps the pull near the edge, which suits applications where a finger grip at the perimeter is preferred rather than a projecting handle. The anodized satin clear aluminum surface works in situations where a subdued metal look is desired, tying into hinges or other visible aluminum components. Being a back mounted pull, it is suited to jobs that prioritize a smooth front surface and a minimalist appearance, since the anchoring takes place from the rear of the panel.
The 1-1/4 inch (32 mm) center to center measurement on this DP47-A pull allows you to base all drilling layouts on a consistent 32 mm spacing, which helps when setting up line boring equipment or drilling jigs. Overall length of 50 mm gives you a clear reference from the door edge to the end of the pull, aiding in aligning multiple pulls so sight lines stay even across a bank of doors or drawers. The design for material thickness of 1/2 inch to 7/8 inch means the pull engages properly within that range, helping maintain a solid connection when used on typical cabinet stock thicknesses. The back mounted style concentrates work on the interior face of the door or drawer front, which allows the front face to stay unbroken while still giving access for fastening from behind. The anodized satin clear aluminum finish provides a stable surface appearance along the edge, which helps projects where consistently matching hardware is important from one cabinet section to the next.
The EPCO DP47-A edge pull has a 1-1/4 inch, or 32 mm, center to center spacing, which defines the distance between mounting holes for layout and drilling.
The EPCO DP47-A aluminum edge pull has an overall length of 50 mm, keeping it compact along the edge while still offering a defined gripping area at the cabinet front.
The EPCO DP47-A edge pull is designed for material thickness of 1/2 inch to 7/8 inch, aligning with common cabinet door and drawer front stock.
The EPCO DP47-A is a back mounted pull, so it installs from the rear side of the door or drawer front, leaving the front surface free of exposed fasteners.
The EPCO DP47-A edge pull is made from anodized satin clear aluminum, giving it a neutral metallic appearance suited to many cabinet styles.
The EPCO DP47-A part number identifies this specific edge pull, which supports consistent hardware selection when matching existing installations on later jobs.
The EPCO edge pull DP47-A combines a 1-1/4 inch (32 mm) center to center layout, 50 mm overall length, and back mounted design for clean cabinet faces. With anodized satin clear aluminum construction and a fit range of 1/2 inch to 7/8 inch material thickness, it suits many cabinet door and drawer applications where compact, consistent hardware placement matters.
Sold In: 1 Each