EPCO Edge Series 3 inch edge pull gives you an anodized satin clear aluminum pull that mounts at the door or drawer edge, so you get a low-profile grip without interrupting flat fronts. The 77mm center to center hole spacing sets a consistent reference between fasteners, which supports accurate layout across multiple cabinet parts. The 100mm overall length adds usable finger clearance along the edge, which helps when opening heavier or taller fronts. The pull is designed for material thickness of 1/2 inch to 7/8 inch, so it covers common cabinet door and drawer front constructions in shops using panel stock. Back mounted design locates all fasteners from the rear face, which keeps the visible edge clean and helps match modern, minimal cabinet runs.
The EPCO aluminum back mounted pull uses a center to center spacing of 77mm, which means drill locations transfer easily from templates or jigs when you are setting up for repeatable production. With an overall length of 100mm, the pull spans a practical section of the door or drawer edge, giving consistent hand placement at the working edge. Its design for material thickness from 1/2 inch to 7/8 inch matches common cabinet stock, so the pull seats at the edge without overhanging thin panels or burying into thicker fronts. The anodized satin clear aluminum finish supports a uniform appearance along runs of cabinets, which matters on visible banks of drawers or doors.
The DP47-A-100 aluminum edge pull sits in Decorative Hardware & Moldings under Handles and Pulls, so it is suited to cabinet and similar casework fronts where a slim grip at the edge is preferred. The 77mm center to center dimension lets the pull sit comfortably on doors or drawers without crowding corners, which helps when spacing hardware on narrow faces. Its 100mm overall length gives the user a defined grab point along the edge, which fits well on both small drawer fronts and mid-sized doors. Because the pull is designed for material thickness of 1/2 inch to 7/8 inch, it matches typical cabinet panels built from sheet goods, which supports consistent hardware selection across a project. The anodized satin clear aluminum finish works in decorative hardware contexts where a neutral metal look coordinates with other components.
The EPCO Edge Series 3 inch edge pull uses a defined 77mm center to center spacing, which supports the use of drilling jigs or CNC programs for accurate and repeatable hole placement. That consistency reduces layout time across multiple fronts and helps maintain straight sight lines along banks of drawers. The 100mm overall length gives a bit of extra length beyond the fixing points, which improves leverage and user comfort when pulling heavier doors or drawers from the edge. Its design window of 1/2 inch to 7/8 inch material thickness means one model covers a spread of front constructions, which can simplify hardware planning on mixed-size jobs. The anodized satin clear aluminum finish provides a controlled surface treatment on the pull, which helps maintain a uniform appearance over time in decorative hardware installations.
The DP47-A-100 edge pull uses a 77mm center to center measurement, which supports consistent drilling layouts and alignment across multiple cabinet doors and drawers.
The EPCO Edge Series pull has an overall length of 100mm, which provides added gripping surface along the cabinet edge for everyday opening and closing.
This aluminum edge pull is designed for material thickness of 1/2 inch to 7/8 inch, aligning with common cabinet door and drawer front panel sizes.
The DP47-A-100 is a back mounted pull, so it is fastened from the rear face, leaving the front edge clean for a minimal appearance.
This EPCO edge pull has an anodized satin clear aluminum finish, which offers a neutral metal look that coordinates with other aluminum decorative hardware.
This anodized satin clear aluminum edge pull suits decorative cabinet and casework installations where a slim edge-mounted handle is preferred.
The EPCO Edge Series 3 inch edge pull, part number DP47-A-100, brings an anodized satin clear aluminum handle with 77mm center to center spacing and 100mm overall length to cabinet projects. Its design for 1/2 inch to 7/8 inch material supports use across standard door and drawer fronts. With back mounted construction, it maintains clean edges for modern decorative hardware runs while giving a defined grip point along the front. For projects needing a straightforward aluminum edge pull with predictable drilling dimensions, this model fits that role.
Sold In: 1 Each