EPCO Edge Series 3" (76 mm) Center to Center Anodized Satin Black Edge Pull, - DP47-BL-100

EPCO Edge Series Edge Pull For Clean Access

EPCO Edge Series edge pull is an anodized satin black aluminum pull designed to mount on the edge of a panel, so doors or drawers open with a low-profile grip instead of a protruding handle. The 3 inch (76 mm) center to center dimension provides a compact hand grab point, which helps on smaller cabinet doors and narrow drawer fronts where space is tight. The 100 mm overall length keeps the pull visually balanced on many standard cabinet widths, tying multiple fronts together in a consistent layout. The back mounted design anchors the pull from the rear of the panel, which keeps the front face free of visible fastener heads and supports a clean look. The satin black anodized finish creates a dark, uniform surface, so the pull visually recedes and supports modern cabinet lines without drawing attention away from the door or drawer face.

Key Edge Pull Details That Support Your Project

• The 3 inch (76 mm) center to center measurement sets a precise drilling pattern, which simplifies layout when repeating the pull across multiple cabinets or drawer banks during a larger install.
• The 100 mm overall length gives a defined edge span, so the pull covers enough length for a comfortable finger grip while still fitting on compact fronts where longer handles would crowd adjacent components.
• The anodized satin black finish creates a consistent dark tone across each pull, which supports uniform color alignment on runs of cabinetry where visual continuity matters.
• The aluminum construction provides a lightweight profile, which reduces mass on the door or drawer edge and contributes to smooth hardware operation alongside hinges or slides.
• The back mounted configuration places the fastener connection on the rear face of the material, which keeps the presentation side clear and helps achieve a streamlined, minimal aesthetic on contemporary work.
• The 3 inch (76 mm) center to center and 100 mm overall length combination sets a compact footprint, which works well when aligning pulls on smaller doors above or below larger fronts in a coordinated stack.

Back Mounted Edge Pull Fit And Setup

The ALUM EDGE PULL,4INL,BACK MOUNTED,BLACK design uses a back mounted approach, so the pull is secured from the rear of the door or drawer material and the front edge shows only the functional grip profile. The center to center dimension of 3 inches (76 mm) defines the hole spacing, which guides drilling locations so multiple pulls line up accurately from cabinet to cabinet. The 100 mm overall length means the body of the pull extends slightly beyond the fixing points, which helps distribute hand force along the edge rather than concentrating it at a single spot. The specified material thickness range of 1/2 inch to 7/8 inch identifies the panel sizes this pull is designed to work with, supporting consistent fit across typical cabinet doors and drawer fronts within that thickness band.

How This Edge Pull Fits Cabinet Workflows

Edge Pull Use On Cabinet Doors And Fronts

The Web Description identifies this item as an ALUM EDGE PULL,4INL,BACK MOUNTED,BLACK with a center to center spacing of 77 mm and an overall length of 100 mm, so it functions as a compact grip along the edge of a door or drawer front. The EPCO Edge Series 3 inch (76 mm) center to center specification ties this pull directly to layouts that are built around that drilling dimension, which is common in many cabinet and furniture runs. Because the pull is intended for material thickness of 1/2 inch to 7/8 inch, it aligns with a typical range of cabinet door and drawer front constructions, from lighter panels to more substantial fronts. The decorative hardware and moldings, handles and pulls classification places this part in a visible hardware role, so it becomes part of the finished appearance as well as the opening function.

Details That Support Consistent Cabinet Results

The combination of 3 inch (76 mm) center to center and 100 mm overall length establishes a repeatable proportion from pull to pull, which helps installers keep sightlines straight and visually balanced across long cabinet runs. The back mounted configuration lets the pull anchor from the rear of 1/2 inch to 7/8 inch material, so the front face remains uninterrupted, supporting a unified surface when doors are closed. The anodized satin black finish gives the edge pull a controlled sheen and color tone, which helps it coordinate with other black elements in the space without introducing reflective distractions. The aluminum construction keeps the component weight low relative to its size, which assists hardware sets that rely on smooth hinge or slide motion by avoiding unnecessary added load on the moving parts.

Common Questions About This EPCO Edge Pull

Select This Edge Pull For Defined Cabinet Layouts

The EPCO Edge Series 3 inch (76 mm) center to center anodized satin black edge pull DP47-BL-100 combines a 100 mm overall length with a back mounted layout and an operating range of 1/2 inch to 7/8 inch material thickness. Those defined dimensions and the aluminum, anodized satin black construction give you a compact, repeatable grip solution for cabinet doors and drawer fronts that need a low-profile edge pull. For projects that call for a consistent drilling pattern and a clean, modern appearance, this edge pull aligns directly with that style of cabinet hardware plan.