Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 72 inch aluminum edge pull provides a continuous pull along a 6 foot length, which supports long cabinet or panel runs where a single, uninterrupted grip improves handling. The pull is made from aluminum, so it adds a functional gripping surface without adding significant bulk to the edge of the material. This DP47-L-M edge pull is part of the EPCO handles and pulls line, tying directly into projects that already use similar decorative hardware. The pull is designed for back mounted installation, so it sits on the rear side of the material edge and presents a clean front appearance on the working face. The length of 72 inches, also noted as 6 feet, streamlines layouts where multiple shorter pulls would otherwise break up the edge. This configuration helps installers set up consistent, easy-to-grab edges on tall cabinets, closet panels, or long doors.
The back mounted aluminum edge pull layout lets the installer work from the rear of the panel, so the visible front face stays clean while the pull still provides a firm edge grip. The 6 foot length gives one continuous handling point along tall or wide elements, which simplifies day-to-day operation of closet doors, cabinet panels, or similar pieces. Because the pull is sized for 1/2 inch to 7/8 inch material, it aligns the gripping profile to this thickness range, helping the edge sit correctly relative to the front and back faces. The DP47-L-M part reference keeps ordering and replacement straightforward, since the same identifier tracks the exact length and configuration used on the project.
This EPCO Edge Series 72 inch aluminum edge pull fits projects that use long vertical or horizontal doors, panels, or fronts where users need an extended handhold. The 6 foot length makes it suitable for tall wardrobe or closet panels, where a full-height grip simplifies opening from different points along the edge. On wide cabinet or storage runs, the continuous pull spans much of the width, so users can pull from either side without searching for a discrete knob. The design for 1/2 inch to 7/8 inch material thickness means it is intended for use with common cabinet panel stock or similar substrates that fall in that range. Because it is back mounted, the pull works well anywhere a clean, flat front is preferred, such as modern casework, where the design relies on straight lines and minimal front hardware detail.
The defined material thickness range of 1/2 inch to 7/8 inch gives a clear window where the edge pull profile is sized to sit correctly on the panel edge, which supports repeatable results across multiple parts. The continuous 72 inch (1829 mm) length means all pull points along that edge share the same alignment, so there is no variation between separate pieces that could otherwise occur with multiple shorter pulls. Aluminum construction keeps the component manageable during handling and positioning along the full 6 foot span, which can help during layout and fastening on tall or wide panels. The back mounted configuration means all work is done from the rear face, allowing installers to align the pull to layout lines without disturbing the finished front surface. Using the EPCO DP47-L-M part number on project documentation ties field installation back to the exact edge pull specification, simplifying future additions or replacements that need to match the original hardware.
The EPCO DP47-L-M edge pull has a length of 72 inches, also described as 6 feet, which lets it span tall or wide panels with a single continuous gripping surface.
The EPCO Edge Series 72 inch pull is aluminum, providing a defined edge grip along the panel while keeping overall weight low across the 6 foot length.
This EPCO aluminum edge pull is back mounted, so it attaches from the rear side of the material and leaves the front face with a clean, uninterrupted look.
The DP47-L-M edge pull is designed for material thickness from 1/2 inch to 7/8 inch, matching common cabinet and panel stock used in many shop projects.
A 72 inch aluminum edge pull is suited to tall doors, closet panels, or long cabinet fronts where a continuous, easy-to-grab edge improves everyday opening and closing.
The EPCO DP47-L-M part number identifies a 72 inch aluminum edge pull from the EPCO Edge Series, helping match the same length and style across a project.
This 6 foot aluminum edge pull from the EPCO Edge Series ties continuous length, back mounted installation, and a 1/2 inch to 7/8 inch material range into one part, DP47-L-M. For projects using tall doors or long panels, this configuration keeps the gripping edge consistent from end to end. When the goal is a clean front face with dependable hand access along the edge, this EPCO aluminum pull provides a defined, repeatable hardware choice for cabinet and panel work.
Sold In: 1 Each