Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO edge pull gives a compact way to operate cabinet doors and drawers where a low-profile grip is preferred. The 32 mm center to center drilling lines up with standard 32 mm layouts, so hole placement stays predictable across cabinet runs. The overall length of 50 mm keeps the pull small, which helps on narrow fronts or tight banks of drawers without crowding adjacent hardware. An anodized oil rubbed bronze finish provides the dark, uniform appearance associated with that color family, so it visually ties in with other oil rubbed bronze elements in the job. The back mounted design fastens from the rear of the material, so the front face stays clear of visible fasteners. Designed as part of the EPCO Edge Series and identified as DP47-ORB, this pull fits projects needing a specific match to that part designation.
The back mounted EPCO edge pull uses rear fasteners through the cabinet material, so alignment depends on accessing the back side during installation. The 32 mm center to center spacing aligns with widely used 32 mm system drilling, supporting repeatable hole placement on line-bored components. With an overall length of 50 mm, the pull stays within a compact footprint, which matters on narrow stiles and rails where longer pulls could overrun the available width. Suitability for material thickness from 1/2 inch to 7/8 inch defines how the pull seats on common cabinet door and drawer stock, so the grip location remains workable across typical construction choices.
This EPCO edge pull is specified for material thickness of 1/2 inch to 7/8 inch, so it fits many cabinet doors and drawer fronts built from common panel stock within that range. The compact 50 mm overall length allows it to sit comfortably on narrow drawer fronts or small doors without overpowering the face. With a 1-1/4 inch (32 mm) center to center drill pattern, it lines up naturally on components laid out on the 32 mm system, which is widely used in cabinet casework. The anodized oil rubbed bronze finish gives a consistent dark tone, so when used across a run of cabinets it maintains a uniform appearance with other oil rubbed bronze decorative hardware. As part of the EPCO Edge Series under part DP47-ORB, it suits jobs that call for that exact model as part of a matched hardware schedule.
The 32 mm center to center dimension on this back mounted EPCO edge pull provides a fixed drilling pattern, which supports jigs or line-boring layouts where repeatability is important across many fronts. The back mounted construction means fasteners pass from the rear through the 1/2 inch to 7/8 inch material range into the pull, creating a clean working face because the front side shows only the pull profile. With an overall length of 50 mm, the pull leaves space near edges on smaller fronts, which can simplify placement relative to door corners or drawer sides. The anodized oil rubbed bronze finish reflects the stated surface treatment, so installers aligning with a specified oil rubbed bronze scheme can match this pull to that requirement. Identification as EPCO DP47-ORB helps tie the installed hardware back to drawings or parts lists that call out that precise number.
The EPCO DP47-ORB edge pull uses a 32 mm center to center dimension, which matches 1-1/4 inch spacing and works with layouts based on the 32 mm cabinet system.
The EPCO edge pull has a 50 mm overall length, keeping the grip compact for use on narrow doors or drawer fronts where space is limited.
The EPCO DP47-ORB edge pull is designed for material thickness from 1/2 inch to 7/8 inch, matching many common cabinet door and drawer stock sizes.
The EPCO edge pull is back mounted, so fasteners go through the rear of the cabinet material into the pull, leaving the front face free of visible fasteners.
The anodized oil rubbed bronze finish on this EPCO edge pull establishes its stated color and surface treatment so it coordinates with other oil rubbed bronze hardware.
The EPCO part number DP47-ORB identifies this specific Edge Series 32 mm center to center anodized oil rubbed bronze edge pull for matching to project specifications.
The EPCO Edge Series DP47-ORB edge pull combines 32 mm center to center spacing, 50 mm overall length, and suitability for 1/2 inch to 7/8 inch material, which aligns well with many cabinet layouts. The anodized oil rubbed bronze finish and back mounted construction support clean, coordinated fronts. For projects calling for these dimensions and this specific EPCO part number, this pull provides a defined option.
Sold In: 1 Each