EPCO edge pull gives a compact grasp point along a cabinet or drawer edge, using a 1-7/16 inch center to center layout that sets consistent hole spacing for repeatable installations across multiple fronts. The 2 inch overall length keeps the pull footprint tight, which helps when working on small doors or narrow drawer faces where larger hardware can crowd edges or clash with adjacent pieces. Satin nickel finish defines the visual tone of the pull, providing a neutral metal look that can coordinate with many hinge and fixture finishes in the same project run. Construction from zinc forms a solid, single-piece body that supports the pull during everyday opening and closing cycles. The 1-1/2 inch projection creates working clearance for fingers behind the pull edge, helping users get a confident grip without needing excessive space in front of the cabinet line.
The 1-7/16 inch center to center spacing on this EPCO edge pull defines exactly where mounting holes land, making it straightforward to set up a drilling pattern or template that repeats accurately from front to front. With the pull length at 2 inches, the ends stay close to the hole pattern, supporting tight placement near corners or rails without overhanging neighboring elements. The 1-1/2 inch projection indicates how far the gripping surface extends from the cabinet face, so installers can plan clearances relative to adjacent doors, walls, or appliance panels. Using #8-32 thread screws ties the pull into a common cabinet fastener system, which helps maintain consistency when mixing this pull with other hardware that relies on the same machine screw standard.
This EPCO edge pull from the Edge Series fits cabinet and drawer fronts where a compact pull is preferred, using its 2 inch length to stay within tight rail or stile dimensions. The 1-7/16 inch center to center measurement places the two mounting points in a narrow span, which works well on smaller doors, vanity fronts, or utility cabinets that do not allow for wide handle spacing. With a 1-1/2 inch projection, the pull sets a defined stand-off that works on fronts which need room for fingers while remaining close enough to the face to preserve a streamlined cabinet profile. The satin nickel finish supports use in projects that coordinate multiple visible metal elements, so the pull can sit alongside satin nickel hinges, knobs, or fixtures in the same installation. Zinc construction keeps the part as a single, solid pull for repeated daily operation wherever a small, edge-mounted gripping point is useful.
The defined 1-7/16 inch center to center spacing on the EPCO edge pull allows installers to rely on a single drilling template, which reduces layout variability and helps doors and drawers line up visually across a bank of cabinets. The compact 2 inch length means each pull occupies only a short section of the front, simplifying alignment with narrow rails and lowering the chance of overhang into panel reveals or into neighboring fronts. The 1-1/2 inch projection creates a fixed working clearance, which aids in planning overlay and reveal relationships so that fingers can comfortably catch the edge pull without contacting adjacent faces. The satin nickel surface maintains one consistent finish reference, helping woodworking teams deliver uniform appearance from one cabinet run to the next. With zinc used as the material, the pull body stays rigid under hand load, supporting long-term cabinet use once mounted with the #8-32 thread screws specified in the product description.
The EPCO edge pull has a 1-7/16 inch center to center spacing, a 2 inch overall length, and a 1-1/2 inch projection, so layout, footprint, and clearance are all clearly defined before drilling.
The 1-7/16 inch center to center spacing sets a fixed distance between mounting holes, allowing installers to use a consistent jig or template for multiple doors and drawers.
The 1-1/2 inch projection defines how far the pull stands off the cabinet face, providing finger room for a comfortable grip while keeping the profile relatively close to the door or drawer.
The EPCO DP48-SN edge pull is made of zinc, creating a solid pull body that handles repeated opening and closing on cabinet doors and drawers in regular use.
This EPCO edge pull has a satin nickel finish, supporting projects that call for a consistent nickel tone across decorative hardware and visible metal components.
The edge pull uses #8-32 thread screws, matching a common cabinet hardware thread standard and helping it integrate with familiar installation practices.
The EPCO edge pull combines a 1-7/16 inch center to center pattern, 2 inch length, and 1-1/2 inch projection, giving clear layout and clearance information before any holes are drilled. Satin nickel finish and zinc construction align with decorative and functional needs on many cabinet runs. With #8-32 thread screws specified, this pull ties into standard cabinet hardware practices, so installers can keep using familiar tooling and thread systems. Choose this DP48-SN edge pull when a compact, satin nickel gripping point is needed along a cabinet or drawer edge.
Sold In: 1 Each