Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO 3 inch almond pull gives a defined 3 inch (76 mm) center to center grip point, which sets consistent drilling and layout across doors and drawers. The plastic construction creates a lightweight pull that is straightforward to handle during cabinet installation and adjustment work. The almond color offers a neutral tone that blends into many cabinet finishes, supporting uniform runs on jobs using light-colored fronts. The handle sits with a 1-1/4 inch projection, providing finger clearance while limiting how far it extends into walkways or tight shop layouts. As part of EPCO handles and pulls, this piece fits into decorative hardware planning where repeatable spacing and a uniform style are priorities. The pull is sold by Wurth Baer Supply in each quantities, so ordering aligns directly with the number of openings on a project.
The defined 3 inch (76 mm) center to center dimension on this EPCO plastic cabinet pull sets clear drilling points, which supports the use of jigs or repetitive boring patterns on cabinet doors and drawer fronts. The 1-1/4 inch projection describes how far the pull stands off the surface, giving installers a predictable profile when checking clearances between neighboring cabinets or adjacent walls. The plastic construction contributes to easier handling during installation because each pull adds minimal weight to the front, which can matter when aligning lighter doors on hinges. The MC302-2-AL designation ties this pull to specific shop documentation, so the same drilling pattern and mounting layout can be repeated reliably on future phases of work.
The 3 inch center to center measurement defines the mounting pattern on cabinet fronts, so this EPCO plastic pull suits layouts already designed around this spacing. On new cabinets, that consistent measurement allows installers to run boring templates that match plans, reducing layout variation between doors and drawers. The defined 76 mm distance also fits metric-oriented shops that reference both inch and millimeter scales during setup. For replacements on existing fronts drilled at 3 inch spacing, the pull aligns to current holes, so the MC302-2-AL part can be used when continuity of spacing is a requirement. Across projects, the documented center to center value helps coordinate with drawings, cut lists, and hardware schedules in a repeatable way.
The 1-1/4 inch projection of this almond plastic pull establishes a steady hand gap, which supports daily use by allowing fingers to hook behind the pull without needing a deep reach. Keeping projection at this dimension helps avoid handles protruding too far over countertops or walk paths, which can matter on tight kitchen or shop layouts. The plastic material keeps each pull light, so it does not add significant load to lighter cabinet doors or small drawer fronts, supporting smoother motion where hardware weight can affect alignment. The almond color ties into decorative hardware and moldings planning, providing a uniform appearance across EPCO handles and pulls on runs of similarly finished cabinets. With the MC302-2-AL identification, the same color and form factor can be referenced later when additional cabinets or matching replacement pulls are required on the same job.
The EPCO 3 inch almond pull has a 3 inch (76 mm) center to center spacing, which sets the exact hole distance for drilling and matching existing cabinet layouts.
The MC302-2-AL plastic pull has a 1-1/4 inch projection, giving practical finger clearance while keeping the handle closer to the cabinet face in narrow areas.
The EPCO 3 inch almond pull is made from plastic, which keeps it lightweight for handling and fastening across multiple cabinet fronts on a project.
The pull carries the EPCO brand and MC302-2-AL manufacturer part number, helping match hardware schedules and simplifying future reorder or replacement needs.
This MC302-2-AL pull is listed under decorative hardware and moldings in the handles and pulls class, fitting cabinet hardware planning work.
The EPCO MC302-2-AL almond pull is sold in each quantities, which aligns ordering with the exact number of cabinet doors and drawers on a job.
The EPCO plastic cabinet pull with 3 inch (76 mm) center to center spacing fits projects built around that common drilling pattern, supporting consistent layouts. The 1-1/4 inch projection and almond plastic construction define how it sits and feels on the front, which matters for everyday cabinet use. With the MC302-2-AL designation and each-based ordering from Wurth Baer Supply, this pull can be specified clearly on plans and matched across new cabinets or replacement work.
Sold In: 1 Each