EPCO 3 inch center to center pull gives you a straightforward handle layout, so drilling or reusing 3 inch hole patterns stays simple on doors and drawers. The 3 inch (76 mm) center to center dimension sets a standard spacing between mounting points, which helps align multiple pulls in a run for consistent sightlines on cabinet faces. The black pull color provides a dark, uniform look that blends into many cabinet styles, so you can coordinate hardware across a room without mixing finishes. The pull uses plastic material, so it keeps weight low on lighter doors and fronts, which is useful on smaller cabinet constructions. EPCO branding identifies the pull within the EPCO handles and pulls class, which helps match this MC302-2-BL part with existing EPCO hardware. The handle works as a practical grip point, so opening and closing cabinets stays controlled and repeatable in everyday use.
The 3 inch (76 mm) center to center dimension defines the hole spacing needed, so when you lay out doors or drawer fronts you can plan a straight drilling pattern using that fixed measurement. The 1-1/4 inch projection controls how far the hand sits off the face, which supports a natural grip without pulling the handle too far into the room. The #8 x 1-1/8 inch self tapping screws are specified as the fasteners, so the pull works with a screw size that matches common cabinet construction thicknesses in many shop-built pieces. The plastic material keeps the pull lighter than many metal options, which can be useful when fastening into thinner fronts where extra weight is not desired. As an EPCO handles and pulls product, this MC302-2-BL pull aligns with typical cabinet hardware patterns used across decorative hardware and moldings projects.
The EPCO 3 inch (76 mm) center to center black pull aligns well with cabinet fronts laid out around that common 3 inch measurement, so it fits neatly on new builds or replacements set to that spacing. The handles and pulls category placement signals that this part is suited to drawers and doors in cabinetry, so it supports typical shop workflows for kitchen, bath, or storage pieces that use decorative hardware and moldings. The black pull finish works where a dark, understated handle is preferred, so it integrates into designs built around dark laminates, painted fronts, or contrasting light surfaces. Because the pull is made from plastic, it suits cabinets where a lighter handle is appropriate, such as smaller doors, modest drawer sizes, or built-ins where limiting hardware weight is part of the design approach. The EPCO brand and MC302-2-BL identifier help keep this handle aligned with other EPCO decorative components, so a shop can maintain consistent hardware sourcing across multiple cabinet runs.
The 3 inch (76 mm) center to center measurement on this EPCO MC302-2-BL pull provides a fixed drilling reference, which supports the use of jigs or templates for repeatable handle placement across a series of fronts. The 1-1/4 inch projection defines the stand-off from the face, so drawer and door clearances can be planned knowing how far the grip extends into the working area. The specified #8 x 1-1/8 inch self tapping screws connect the pull through the cabinet material, so fastening relies on a known screw diameter and length that align with many cabinet panel thicknesses. This plastic pull construction reduces stress at the fastener interface compared with heavier pieces, which can be important on thinner materials. As a handles and pulls, EPCO product, this part integrates into hardware layouts where matching EPCO pulls are used repeatedly, helping shops keep layouts and hardware choices consistent from one project section to the next.
The EPCO MC302-2-BL pull has a 3 inch (76 mm) center to center size, so hole spacing follows that common cabinet layout dimension for doors and drawers.
The MC302-2-BL pull projects 1-1/4 inch from the surface, providing finger clearance behind the handle while keeping the grip close to the door or drawer front.
The EPCO 3 inch center to center black pull is made from plastic, so the handle remains lightweight on cabinet doors and drawer fronts.
The MC302-2-BL pull is specified with #8 x 1-1/8 inch self tapping screws, so mounting uses a familiar screw size in many cabinet materials.
This EPCO MC302-2-BL pull is listed under decorative hardware and moldings in the handles and pulls class, so it fits typical cabinet handle applications.
The manufacturer part number MC302-2-BL identifies this EPCO 3 inch center to center black pull, which helps align it with matching EPCO hardware.
The EPCO 3 inch center to center black pull combines a standard 3 inch (76 mm) hole spacing, a 1-1/4 inch projection, and plastic construction, so it fits straightforward cabinet handle layouts. The MC302-2-BL identifier, black finish, and specified #8 x 1-1/8 inch self tapping screws all work together to define how this pull mounts and looks on finished fronts. For projects built around EPCO decorative hardware, this handles and pulls part offers a consistent option when planning new cabinet runs or updating existing fronts.
Sold In: 1 Each