EPCO Wire Series aluminum pull gives you a 2-1/2 inch (64 mm) center to center handle that lines up cleanly with standard 64 mm boring patterns, so layout is straightforward on cabinet doors and drawers. The handle uses an M4 thread, so it matches common metric mounting patterns in cabinet hardware projects. Its projection is 1-5/16 inches, which keeps fingers clear of the door or drawer face during use while keeping the pull compact on smaller fronts. The pull is made from aluminum, providing a light, rigid grip point that keeps weight down on moving fronts. An anodized satin clear finish on the aluminum creates a uniform, low-gloss surface that blends into many cabinet styles while allowing the metal to show through. Each pull is sold individually, so counting for multi-opening runs stays simple on the job.
This EPCO aluminum wire pull is defined by its 64 mm center to center spacing, so boring or drilling uses that exact dimension between holes for correct alignment. The M4 thread on the pull interfaces with M4 threaded fasteners, allowing it to seat securely into properly sized holes during mounting on cabinet fronts. With a 1-5/16 inch projection off the surface, the pull provides hand clearance while still staying tight to the face, which matters on doors that open near adjacent cabinets. The anodized satin clear aluminum finish offers a consistent surface during handling and installation, so the pull maintains an even appearance after it is mounted across a full bank of fronts.
This EPCO Wire Series aluminum pull with 2-1/2 inch (64 mm) center to center sizing is suited to cabinet and drawer fronts drilled on a 64 mm layout, so it integrates well into metric-based cabinetry. On upper cabinets, the 1-5/16 inch projection gives enough stand-off for fingertips to hook the pull even when doors are mounted higher, while its compact reach keeps the profile modest. On base cabinets and drawers, that same projection creates a consistent grip depth, which helps maintain a uniform feel when opening different fronts in the same run. The aluminum construction keeps each pull light on taller doors, which matters where multiple pulls are stacked vertically. The anodized satin clear finish allows this pull to visually coordinate with other satin-finished decorative hardware pieces in a project built around similar aluminum tones.
The 64 mm center to center dimension of the MC404-64-A aluminum wire pull supports repeatable drilling patterns from cabinet to cabinet, helping keep reveals and sight lines consistent across whole walls of casework. By relying on an M4 thread, the pull ties directly into metric system hardware planning, so thread engagement and hole sizing stay predictable from one front to the next. The 1-5/16 inch projection controls how far the pull stands off the face, which affects both clearance for fingers and spacing relative to nearby doors, drawers, or walls. The anodized satin clear surface treatment on the aluminum produces a stable finish that visually unifies banks of cabinets when identical pulls are used throughout a room. Each pull being sold as each lets installers match quantities accurately to drawing counts or opening schedules.
The EPCO Wire Series aluminum pull has a 2-1/2 inch (64 mm) center to center dimension, which matches a 64 mm boring pattern for consistent cabinet and drawer handle alignment.
The MC404-64-A pull uses an M4 thread, so it matches metric-thread mounting points on cabinet fronts and aligns with hardware that is designed around M4 fasteners.
The EPCO aluminum pull projects 1-5/16 inches from the mounting surface, providing space for fingers to grip the handle while keeping the pull relatively compact on the front.
The pull is made from aluminum with an anodized satin clear finish, giving it a light metal body and a neutral satin appearance for many cabinet hardware layouts.
This EPCO Wire Series aluminum pull is sold as each, so quantities can be matched to the exact number of cabinet doors and drawers on a project.
The 64 mm center to center dimension suits cabinet and drawer fronts drilled on a 64 mm metric layout, supporting consistent spacing across residential or commercial casework.
The EPCO Wire Series aluminum pull MC404-64-A brings a 2-1/2 inch (64 mm) center to center layout, 1-5/16 inch projection, and M4 thread together in a compact handle for cabinets. Its aluminum construction with anodized satin clear finish supports projects planned around neutral satin metal hardware. Sold individually through Wurth Baer Supply, it fits runs where counts follow exact cabinet and drawer schedules. For casework based on 64 mm spacing, this pull delivers a consistent mounting pattern and appearance across the installation.
Sold In: 1 Each