EPCO oak pull 96mm center to center gives cabinet doors and drawers a wood handle sized for common 96 mm drilling, which keeps layout straightforward on new work or when matching existing 96 mm runs. The pull uses an oak construction, so it visually ties into oak fronts and trim where a natural wood grip is preferred over metal. Its 4-9/16 inch overall length spans a door or drawer face with enough hand contact for a solid grasp during daily use. A 1-25/32 inch width provides a comfortable gripping surface while leaving room around the pull for finishes and reveals. The 27/32 inch projection sets the handle off the face far enough for fingers to wrap behind without feeling overextended, which helps doors open smoothly. This pull is listed as surface mount, so it fastens directly to the cabinet face, simplifying installation on standard cabinet construction.
This EPCO wire series pull is specified as surface mount, so it attaches directly to the cabinet face using through-bored holes at 96 mm center to center. That mounting style suits typical cabinet construction where a straightforward bore through the door or drawer front is all that is required. The 27/32 inch projection controls how far the pull stands off the face, which affects how the hardware feels in hand when pulling doors open. With its 4-9/16 inch overall length, the pull positions mounting points near the ends while leaving a clear gripping area centered on the panel. A width of 1-25/32 inch gives the installer a defined footprint to align parallel with door edges, helping maintain straight sight lines across multiple fronts.
The EPCO WP26 wood pull sits in the Decorative Hardware & Moldings, Handles and Pulls category, so it is oriented to cabinet and furniture applications where visible hardware also contributes to the finished look. Its oak material matches projects that feature natural or finished oak doors, drawer fronts, or trim, allowing the handle to read as part of the woodwork rather than a contrasting element. The 96 mm center to center drilling is suited to base and wall cabinets, vanities, and storage pieces that follow common metric boring patterns. With a 4-9/16 inch overall length, the pull works well on both doors and medium-width drawers, giving enough span for a centered grip without overpowering narrower fronts. The 1-25/32 inch width presents a solid face to grab, which can be useful on tall pantry doors that see frequent use.
The defined 96 mm center to center spacing on the EPCO WP26 makes boring jigs and line boring setups straightforward, which helps installers repeat hole locations accurately from one front to the next. The 27/32 inch projection is set to balance clearance and visual profile, so rows of pulls sit off the face consistently without appearing too shallow or too proud. Its 4-9/16 inch overall length gives a fixed reference when laying out hardware positions relative to door edges or drawer top rails, helping keep hardware alignment uniform across a bank of cabinets. The 1-25/32 inch width adds enough face area that slight variations in boring do not crowd the pull against panel edges, which can reduce rework on finished fronts. With the EPCO brand and WP26 part number, shops can document the exact pull used, supporting consistent ordering and installation on repeat projects or later additions that must match existing cabinets.
The EPCO WP26 oak pull uses a 96 mm center to center drilling pattern, which matches common cabinet boring layouts for straightforward alignment on doors and drawers.
The 27/32 inch projection holds the pull off the cabinet face enough for fingers to wrap behind, supporting comfortable opening without knuckles rubbing the door or drawer surface.
The EPCO WP26 oak pull has a 4-9/16 inch overall length and 1-25/32 inch width, giving a noticeable but controlled footprint for doors and drawers.
The EPCO WP26 is described as a surface mount pull, so it fastens through the front using holes drilled at 96 mm center to center.
The oak material on this EPCO pull lets hardware visually blend with oak cabinet doors, drawers, and trim, supporting a coordinated wood-focused appearance.
The WP26 part number identifies this specific EPCO wood pull within the Handles and Pulls class, helping shops reorder the same style for future or matching work.
The EPCO oak pull 96mm center to center combines metric drilling, surface mount installation, and a 4-9/16 inch overall length to suit typical cabinet and furniture work. Its oak construction supports projects built around oak doors, drawer fronts, or trim, letting the handle read as part of the wood design. With defined dimensions for center to center, projection, width, and length, this WP26 pull gives installers clear layout references across a run of cabinets. Use this EPCO WP26 when a wood pull with 96 mm spacing and straightforward surface mounting fits the project requirements.
Sold In: 1 Each