Berenson Tempo Series 30-1/4" (768 mm) Center to Center Brushed Nickel Pull, - 1133-2BPN-P

Berenson Tempo Pull For Long Cabinet Runs

Berenson Tempo Series brushed nickel pull is a long, steel cabinet handle designed to span wide drawer and door fronts. The 30-1/4 inch overall length creates a continuous gripping line across larger fronts, which helps keep big faces looking visually balanced on installed runs. The 768 mm center to center drilling dimension sets the exact hole spread, so layouts on new cabinets or replacements can be planned around a known measurement. The brushed nickel finish gives the steel pull a muted sheen that works with many transitional designs, supporting projects that bridge traditional and contemporary fronts. A 1-1/4 inch projection sets how far the pull stands off the surface, giving fingers room to wrap around without sticking too far into the walkway. The 25/32 inch hand clearance defines the usable gap behind the pull, which matters when hands are wet or gloved.

Key Tempo Series Pull Details That Matter

• The 30-1/4 inch length or diameter spreads load across wide doors or drawers, which helps reduce stress around each fastener area on heavy cabinet fronts.
• The 768 mm center to center dimension provides a repeatable drilling layout, which supports consistent alignment across banks of doors and drawers on a run.
• The 1-1/4 inch projection establishes working stand-off, which helps fingers find a reliable grip without the pull catching clothing on tight galley-style installations.
• The 1/2 inch width keeps the pull visually slim, which helps it sit cleanly on narrow rail sections and avoids crowding surrounding trim or adjacent hardware.
• The 25/32 inch hand clearance sets the finger space behind the pull, which aids comfortable access for different hand sizes along the full handle length.
• The 3/8 inch base diameter defines the footprint at each mounting point, which guides how much flat surface is needed around screw holes on the cabinet face.

Installation Dimensions For Accurate Tempo Fit

The 768 mm center to center measurement on this Tempo Series pull is the critical drilling reference, because it dictates exact hole spacing when laying out new fronts or swapping from another pull with the same spread. The 30-1/4 inch overall length shows how much linear space the hardware covers, which matters when positioning near door edges or stacked drawers. A 1/2 inch width and 3/8 inch base diameter define how much flat rail or stile face is engaged, supporting clean seating on standard cabinet frame sections. The 1-1/4 inch projection and 25/32 inch hand clearance work together to define working ergonomics, giving enough reach behind the pull while still keeping the hardware close to the face for tight interiors.

Using This Brushed Nickel Pull On Projects

Where The Tempo Series Pull Fits Best

This Berenson Tempo Series pull, with its 768 mm center to center dimension, is sized for long cabinet applications such as wide drawers or tall pantry doors, where smaller pulls can look out of scale. The 30-1/4 inch overall length gives designers a single continuous handle across broad surfaces, which helps front panels read as one controlled element instead of a cluster of short pieces. Its brushed nickel finish supports transitional style work, since the muted metallic surface pairs with both painted and stained fronts without drawing excessive attention. The 1/2 inch width keeps the profile lean across narrow frames, which helps when aligning hardware near edge details or glass lites. The defined 3/8 inch base diameter also aligns well with typical frame widths, giving a clear bearing area at each mounting point. Because the pull is made from steel, it provides a solid-feeling handle along the full 30-1/4 inch length during repeated daily use.

Details That Support Consistent Cabinet Results

The precise 768 mm center to center spacing on this Tempo pull supports jig-based drilling, which helps installers repeat hole placement accurately across multiple cabinets in a run. The 1-1/4 inch projection ensures the handle stands off the face at a predictable distance, so clearances to adjacent doors and walls can be planned from a known value. With 25/32 inch hand clearance, there is a defined working gap behind the pull, supporting comfortable gripping even when approaching from the side along long drawer banks. The 1/2 inch width and 3/8 inch base diameter simplify layout on narrow rails, because installers can read exactly how much flat surface is occupied at each support point. The brushed nickel finish on the steel body provides a consistent surface appearance along the entire length, supporting visual continuity when multiple pulls from the Tempo Series are aligned on the same project.

Common Questions About The Tempo Series Pull

Selecting This Tempo Pull For Wide Fronts

The Berenson Tempo Series brushed nickel pull combines a 768 mm center to center layout, 30-1/4 inch overall length, and steel construction to address wide cabinet fronts with one continuous handle. The defined projection, width, hand clearance, and base diameter provide clear working dimensions, so layouts and drilling patterns can follow exact measurements on new installations or replacements where these values match existing setups.