Practica 250 Drilling jig for AvanTech YOU

Practica 250 Drilling Jig For AvanTech YOU Drawers

Practica 250 drilling jig is designed for drilling holes for connecting the front panel to AvanTech YOU drawers and pot-and-pan drawers, so installers can position front connections in the pattern the system expects. This focus on the AvanTech YOU drawer and pot-and-pan drawer connection points helps cabinet shops and installers repeat the same front layout across multiple pieces without continual layout work. The jig is made for this front-panel connection task, so it targets the interface that determines how the drawer front lines up to the AvanTech YOU drawer system. By centering on this defined drilling job, the jig supports a consistent process whenever the front panel must connect to the drawer or pot-and-pan drawer components in the same way. The drilling jig role in this connection sequence keeps the drilling step aligned to the AvanTech YOU system geometry from one installation to the next.

Key Practica 250 Details For Daily Use

• The Practica 250 drilling jig is specified for AvanTech YOU drawer and pot-and-pan drawer front-panel connection holes, which keeps the drilled pattern matched to that drawer system when setting up repeat production or installation runs.
• Hardened steel drilling bushes for a 10 mm drill bit guide the bit during drilling, so the bit tracks through a fixed bore and holds the position expected by the front panel connection points over repeated use.
• The drilling bushes are sized for a 10 mm drill bit, creating a defined hole diameter that matches the 10 mm drilling requirement, which helps keep front connections consistent whenever the same bit diameter is used.
• A depth setting ring is specified with the 10 mm drill bit, which sets how deep the bit can travel and helps prevent over-drilling through the front panel zone linked to the AvanTech YOU connection area.
• The drill bit has a hexagonal shaft according to the description, so it can seat in hex-compatible chucks and transmit torque without spinning in the chuck under normal drilling loads during drawer front work.
• The overall length is specified as 112 mm, which gives installers a known reach for engagement through the drilling bushes into the front panel area while staying within the depth range controlled by the setting ring.

Drilling Setup For Front Panel Connection Work

Practica 250 drilling jig focuses on drilling holes for the front panel connection to AvanTech YOU drawers and pot-and-pan drawers, so the drilling setup is centered on that attachment line rather than general cabinet layout. The jig description highlights hardened steel drilling bushes for a 10 mm drill bit, meaning the bushes guide the bit during the drilling pass and keep it aligned where the connection hardware engages the front. With a 10 mm drill bit used through these bushes, the installer works to a fixed diameter that matches the described drilling bushes and front connection layout. The depth setting ring works with the 10 mm drill bit to fix the penetration depth into the front panel zone, so the drilling step can be repeated on additional fronts without manually gauging the depth every time.

Using The AvanTech YOU Practica 250 On Drawer Fronts

Where The Practica 250 Jig Fits Into Work

The Practica 250 drilling jig is specified for drilling holes for connecting the front panel to AvanTech YOU drawers and pot-and-pan drawers, so it fits directly into the step where the front is prepared for attachment. By focusing on the front panel to drawer connection, the jig is applied at the moment when the drawer front must align with the AvanTech YOU drawer or pot-and-pan drawer connection layout. Hardened steel drilling bushes for a 10 mm drill bit guide the drilling through defined paths, so the jig sits at the interface between the front panel and the AvanTech YOU drawer pattern. That definition of use places the jig wherever AvanTech YOU drawers or pot-and-pan drawers require front panels drilled to their connection pattern, supporting shops that repeat this drawer system across job lines or production batches.

Why Practica 250 Details Support Repeatable Results

The Practica 250 drilling jig description specifies hardened steel drilling bushes for a 10 mm drill bit, and this construction guides the bit in a fixed channel that resists wear under normal drilling, so front panel holes stay in predictable locations over repeated operations. The 10 mm drill bit size specified for these bushes sets the drilling diameter to the dimension the AvanTech YOU front connection expects, which supports consistent engagement with the connection interface on drawer and pot-and-pan drawer applications. A depth setting ring is described for the 10 mm drill bit, so depth is physically limited to a defined range during drilling and the front panel receives a consistent bore depth across multiple fronts. The drill bit hexagonal shaft detail supports torque transfer in hex-compatible chucks, which helps the bit stay locked in while working through the hardened steel bushes and front material. With an overall length of 112 mm specified, the bit works within a known reach that matched to the jig layout, so travel through the bush and into the front panel remains controlled during the drilling routine.

Common Practica 250 Drilling Jig Questions

Select Practica 250 For AvanTech YOU Front Drilling

The Practica 250 drilling jig is described specifically for drilling holes for connecting the front panel to AvanTech YOU drawers and pot-and-pan drawers, so it targets that drawer-family connection layout rather than general cabinetry. With hardened steel drilling bushes sized for a 10 mm drill bit, along with a depth setting ring, hexagonal shaft, and 112 mm overall length, the jig and bit combination are defined around the AvanTech YOU front-panel drilling task. When that AvanTech YOU front connection pattern is part of the work, selecting the Practica 250 drilling jig aligns the drilling process with the described system geometry.