
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
SlideLine M double track runner profile gives sliding cabinet doors a defined running path by providing a 2-track runner profile without holes, so the door elements travel in a guided line that suits inset sliding door layouts in cabinetry. At 2500mm length, the runner profile spans long cabinet runs in one continuous piece, which helps installers set up sliding doors over wider openings with fewer joints across the span. The aluminum construction creates a rigid guiding base, which matters when doors cycle along the full 2500mm length in daily use. Because this runner profile is designed as sliding door hardware, it becomes the core track element in a sliding system rather than a simple trim piece, directly affecting how smoothly the doors move. The silver anodized finish defines the visible surface tone, which matters wherever the track edge is exposed at the cabinet front or interior and needs to coordinate with other hardware finishes.
The 2-track runner profile without holes lets installers position fixings only in the screw slot, which gives flexibility in locating screws along the length while keeping the track face clean. Attachment by screwing on in the screw slot means the profile is secured through this dedicated channel, so loads from sliding doors transfer into the cabinet through the screw line rather than through random points. When attachment using suitable adhesive tape is used, the profile is bonded continuously along its back, which spreads support across the length where the substrate and tape system are appropriate. The 2500mm length provides extended reach along cabinet tops or bottoms, so full-width tracks can be set without splicing shorter sections in many common cabinet dimensions.
The runner profile is identified as sliding door hardware for cabinets, so it serves in applications where door panels move laterally instead of swinging on hinges. Because two runner profiles must be fitted per 2-door or 3-door cabinet, one profile can be used at the top and one at the bottom of the cabinet to guide each sliding door set. The 2-track runner profile without holes is suited to 2-door or 3-door cabinet layouts that require two running tracks, giving each door panel a defined lane within the sliding system. The 2500mm length means the same profile can be used on wider cabinet bodies such as wall units or storage runs that demand extended sliding travel. The aluminum, silver anodized body aligns with metal-based sliding systems, making this piece the structural path that other sliding door components rely on during operation.
The 2-track runner profile without holes concentrates its structural role in the track geometry rather than in punched fastening points, helping the doors run across a smooth internal track section. Attachment by screwing on in the screw slot focuses mechanical fastening in a single longitudinal slot, which can support consistent clamping pressure along the cabinet structure during installation. Attachment using suitable adhesive tape allows the profile to be held along its length where tape and substrate are compatible, promoting continuous support directly behind the track body. Two runner profiles must be fitted per 2-door or 3-door cabinet, so each cabinet gains a matched upper and lower running path that stabilizes door panels as they move. The aluminum, silver anodized construction provides a metallic track surface that pairs with sliding door components designed for this material, contributing to the overall sliding motion within the Hettich sliding door hardware system.
The runner profile is sliding door hardware, so it is used as the track element in cabinet sliding door systems where doors travel along defined runners.
The runner profile is 2500mm long, allowing it to span wider cabinet openings in a single piece for continuous sliding door travel along that length.
The runner profile allows attachment by screwing on in the screw slot or attachment using suitable adhesive tape, giving two defined mounting approaches for cabinet installations.
The runner profile requires two runner profiles to be fitted per 2-door or 3-door cabinet, establishing matched tracks to guide the sliding doors.
The runner profile is aluminum, silver anodized, providing a metallic track body with a silver anodized surface in sliding door hardware assemblies.
The runner profile is described as 2-track runner profile without holes, so fixation occurs in the screw slot or by adhesive tape rather than through pre-drilled face holes.
The SlideLine M double track runner profile as a 2-track runner profile without holes gives cabinet projects a defined sliding path in a 2500mm length that suits wider openings. With attachment by screwing on in the screw slot or attachment using suitable adhesive tape, installers gain two mounting options tied directly to this profile. Two runner profiles must be fitted per 2-door or 3-door cabinet, so ordering follows a clear count per cabinet. For sliding door hardware projects using an aluminum, silver anodized track from Hettich America Corporation, this runner profile from Wurth Baer Supply aligns with keyed part number 9227183.
Sold In: 1 Each