3" Wide x 28" High Square Rockwell Single Table Leg, Brushed Steel

3 Inch Wide Square Rockwell Table Leg Details

3 inch wide 28 inch high square Rockwell single table leg defines this component as a dedicated support for work surfaces and tables, so it can be selected as a specific structural leg when planning a layout. The 28 inch high dimension sets it in the standard table height range, which helps when matching work surfaces to typical sitting-height applications across a project. Its square 3 inch width gives the leg a defined footprint at the floor and under the top, so spacing and clearances can be laid out with predictable geometry. The brushed steel description identifies the finish and material appearance, guiding coordination with other metal components and giving a consistent visual across multiple legs. Being identified as a single table leg establishes that each unit serves one support position, which lets quantities be calculated directly from the number of corners or intermediate supports in the design.

Key Rockwell Table Leg Traits For Projects

• The 3 inch wide square profile provides a defined, uniform bearing area at both floor and top contact points, which helps plan leg placement relative to edges and corners on work surfaces.
• The 28 inch high measurement sets a predictable top height when combined with work surface thickness, which supports consistent ergonomics across multiple tables in the same space.
• The brushed steel designation describes a specific surface finish and look, allowing this leg to visually align with other brushed metal components in the same room or installation.
• The manufacturer part number 876-7S-ST precisely identifies this configuration, which supports clear reordering or matching to existing Rockwell legs already installed on a site.
• Being classified under work surface and tables as a table leg defines its intended role as vertical support, so it can be specified confidently for that use within woodworking projects.

Mounting And Adjustment Characteristics Of This Leg

This Rockwell single table leg uses a 4 9/16 inch square mounting plate, which provides a broad, even interface where the leg meets the underside of the work surface, helping distribute load across a known footprint. The 4 9/16 inch by 4 9/16 inch plate dimension lets hole locations and clearances be laid out in a repeatable pattern when multiple legs are used on a run of tables. An adjustable foot with 1 1/8 inch of travel is integrated into the leg, giving vertical adjustment range that can compensate for floor irregularities or align several tops to the same finished height. The presence of this 1 1/8 inch adjustable foot means a nominal 28 inch high leg can be fine-tuned in the field, which is useful when working with existing floors and neighboring casework.

Using This Brushed Steel Leg In Real Projects

Where This Rockwell Table Leg Fits Best

The 3 inch wide x 28 inch high square Rockwell single table leg is positioned for work surface and table applications, as indicated by its category listing under work surface and tables. This orientation defines it as a vertical support suited to common table-height installations, from individual workstations to shared tops. The square plan form combined with the 4 9/16 inch square mounting plate creates a consistent geometry at both ends, which helps when aligning multiple legs under rectangular or straight-edged surfaces. Because the leg is specified as brushed steel, it naturally aligns with other brushed metal elements, allowing a cohesive appearance across table legs, supports, and exposed hardware in the same environment. The product class designation as a table leg reinforces its primary role in supporting horizontal surfaces rather than serving as cross-bracing or decorative trim, so it can be assigned as the main load-bearing element under a top.

How Design Details Support Consistent Results

The 28 inch high specification sets a clear starting dimension when calculating finished work surface height, so installers can account for top thickness and the 1 1/8 inch adjustable foot range to achieve a targeted elevation. That 1 1/8 inch adjustable foot allows fine adjustments after the leg is in position, which can be especially useful when neighboring cabinets or existing work surfaces must align along a common plane. The 4 9/16 inch square mounting plate defines the interface area on the underside of the top, so drilling patterns or reinforcement locations can be repeated from table to table for consistent production. The defined 3 inch width of the square leg provides predictable visual mass and clearance, which matters when positioning legs near chair locations or edges where knees and movement paths are planned. The exact manufacturer part number 876-7S-ST ties all of these traits together in a single identifier, supporting straightforward duplication of the same leg style on future projects or expansions.

Common Questions About This Rockwell Table Leg

Selecting This Rockwell Leg For Your Next Surface

The 3 inch wide x 28 inch high square Rockwell single table leg in brushed steel offers defined dimensions, a 4 9/16 inch square mounting plate, and a 1 1/8 inch adjustable foot, which together support predictable planning and alignment when building or expanding work surfaces and tables.