DH Casters Lock With 6" Wheel, Plate Mount - C-FL6

DH Casters Lock With 6 Inch Wheel For Stable Positioning

DH Casters lock with 6 inch wheel combines welded steel construction and a non-slip rubber pad to hold plate mounted casters steady when equipment needs to stay put, which helps maintain control on the job. The floor lock design operates by foot, so the operator can engage or release the holding force while keeping hands on the load or frame. The overall height range of 6-1/2 to 7-1/2 inches lets the lock work with caster setups built to that operating height, which helps match support position to existing installations. As a plate mount component, it fits into builds that use plate mounted casters rather than stem styles, which supports consistent mounting layouts in carts, racks, or mobile stands.

Key Floor Lock Details That Support Daily Use

• Welded steel construction creates a rigid floor lock body, which helps the unit resist flexing under load and supports repeatable positioning performance over time.
• The non-slip rubber pad provides the ground contact surface, which increases friction at the floor so the locked caster setup holds better when force is applied to the equipment.
• Foot-operated action allows engagement and release with a pedal-style motion, which keeps the operator upright at the side of the unit and speeds routine locking cycles.
• The plate size of 3-15/16 inches by 4-1/2 inches defines the mounting footprint, which lets builders lay out matching plates on frames or carts before drilling mounting locations.
• Plate hole spacing from 2-5/8 inches by 3-5/8 inches to 3 inches by 3 inches gives a defined bolt pattern window, which helps align the lock with common plate mounted caster hole layouts.
• The 3/8 inch attaching bolt callout specifies the fastener diameter for the plate holes, which simplifies hardware selection during fabrication and supports consistent clamping of the lock to the frame.

Mounting And Height Details For Plate Installations

The DH Casters C-FL6 floor lock uses a plate mount design with a 3-15/16 inch by 4-1/2 inch plate, which lets fabricators tie it into structural members sized for standard caster plates. Plate hole spacing from 2-5/8 inches by 3-5/8 inches to 3 inches by 3 inches establishes where mounting holes land on the supporting frame, which aids layout for drilling or slotted mounting strips. The specified 3/8 inch attaching bolt works with the plate holes, which allows the installer to select a single bolt size for each point and keep assembly straightforward. The overall height range of 6-1/2 to 7-1/2 inches relates directly to caster stack height, so the lock can be located to contact the floor as the wheel setup carries the load.

Using This Floor Lock In Mobile Equipment Builds

Where This DH Casters Floor Lock Fits Best

This DH Casters plate mount floor lock belongs in builds that already rely on plate mounted casters, because the 3-15/16 inch by 4-1/2 inch plate ties neatly into rectangular plate mounting zones on carts or frames. The floor lock works with systems where the caster and frame geometry create an overall operating height between 6-1/2 and 7-1/2 inches, so the rubber pad can contact the floor when the unit is engaged. In shops or facilities where a single person often positions mobile stands or carts, the foot-operated mechanism allows the operator to tap the actuator while controlling the load, reducing the need to bend down during frequent moves. The welded steel construction suits equipment that sees repeated motion and directional changes, because the rigid body resists distortion as the floor pad takes vertical force during locking.

Why The Verified Details Matter For Repeatable Results

The non-slip rubber pad on the locking foot translates the internal force of the welded steel body into friction at the floor, which helps maintain hold when workers push or pull on the structure. By calling out plate hole spacing from 2-5/8 inches by 3-5/8 inches to 3 inches by 3 inches, the C-FL6 floor lock gives builders a known bolt pattern window, which supports accurate drilling jigs and speeds repeat installations across multiple carts. The 3/8 inch attaching bolt dimension keeps fastener choice consistent across all plate holes, which simplifies inventory and helps apply even clamping force around the plate perimeter. Because the unit is designed with a 6-1/2 to 7-1/2 inch overall height range, installers can align the lock so the rubber pad reaches the floor as the caster-mounted equipment sits at working height, which allows the lock to share vertical load effectively.

Common Questions About The DH Casters C-FL6 Floor Lock

Choose The C-FL6 Floor Lock For Plate Mounted Builds

The DH Casters lock with 6 inch wheel pairs welded steel construction with a non-slip rubber pad and a plate mount design, giving builders a defined way to hold plate mounted casters steady. With a 3-15/16 inch by 4-1/2 inch plate, plate hole spacing from 2-5/8 inches by 3-5/8 inches to 3 inches by 3 inches, and 3/8 inch attaching bolt sizing, this C-FL6 floor lock offers clear mounting and fastening dimensions for carts, racks, and mobile stands built around plate mounted casters.