DH Casters swivel caster with 3 inch rubber wheel with brake, plate mount 220lb capacity - C-ML3P1RS provides a total locking caster that locks both the wheel and the swivel. This total locking function holds carts and equipment in place when parked, which helps maintain position during loading, unloading, or fine positioning. The caster uses a rubber wheel, so the tread works with the floor instead of marking it, supporting use around finished surfaces. A 220 lb load capacity per caster supports medium-duty institutional carts and equipment where controlled movement is needed. The caster is plate mounted, so it fastens to a flat mounting surface on the equipment frame. This caster belongs to the plate mount product class, placing it in a familiar format for many carts and fixtures. The product is built as a swivel type, so it rotates for steering in tight aisles and work areas.
This plate mount swivel caster uses a plate size of 2-3/8 inch by 3-5/8 inch, so it fastens to equipment with a rectangular footprint common to many medium casters. The plate mount format supports a broad, flat interface with cart frames, which helps distribute the 220 lb load at each mounting point. As a plate mount product class caster, it fits frames designed with flat mounting pads rather than stem sockets. The swivel design sits above the wheel, allowing the caster to rotate as loads are pushed or pulled, which aids in aligning wheels with the travel direction. The total locking mechanism works at the caster, so the operator can stop both wheel rotation and swivel rotation at the mounting point.
This caster is specified for institutional carts, where its 220 lb load capacity and swivel action support routine material movement in schools, hospitals, or similar settings. On food service equipment, the plate mount and floor-protective rubber wheels support use around serving lines and prep areas where floors must remain in serviceable condition. On store display fixtures, the swivel caster with brake allows merchandising units to roll into position and then stay put under the total locking function. Industrial products that remain in the medium-load range can use this caster where occasional relocation is required. Film and movie equipment applications benefit from the smooth swivel and rubber wheel behavior, which help move stands or carts on set while respecting finished floor surfaces. Automotive equipment within the stated load range can use this caster to shift tools or devices around bays in a controlled manner.
The total locking casters feature that both the wheel and the swivel are locked gives more secure positioning than a wheel-only brake, which matters when loading or unloading equipment on slightly sloped or busy floors. The double ball bearing swivel raceway keeps the swivel motion smooth, which assists with precise steering around equipment or fixtures in tight service areas. The 3 inch wheel diameter interacts well with common hard floors, which supports predictable rolling when users push or pull carts. The 1-1/4 inch tread width and floor-protective rubber wheels help distribute loads while being easier on floors, which is valuable where repeated moves occur near customer areas or sensitive surfaces. The zinc plated finish on the caster body supports appearance and surface protection in indoor commercial environments, which helps the caster continue to function smoothly during regular service cycles.
The DH Casters swivel caster uses a rubber wheel, which provides a floor-protective tread suitable for institutional, commercial, and equipment environments listed in the product applications.
The C-ML3P1RS caster has a 220 lb load capacity, which allows it to carry medium-duty loads on carts and equipment within that rating per caster position.
The plate mount swivel caster has a 3 inch wheel diameter and a 1-1/4 inch tread width, which sets the overall rolling profile and contact area on the floor.
The total locking caster function locks both the wheel and the swivel, which holds carts and fixtures in a fixed orientation when parked for loading or display.
The caster is listed for institutional carts, food service equipment, store display fixtures, industrial products, film and movie equipment, and automotive equipment, which frames its intended application range.
The caster uses a plate mounting type with a plate size of 2-3/8 inch by 3-5/8 inch, which matches frames designed for a rectangular plate interface.
This DH Casters swivel caster with 3 inch rubber wheel with brake, plate mount 220lb capacity - C-ML3P1RS combines a total locking caster design, plate mount format, and floor-protective rubber wheel. The 2-3/8 inch by 3-5/8 inch plate, 3 inch diameter wheel, and 220 lb load capacity define its role on institutional carts, food service equipment, store display fixtures, industrial products, film and movie equipment, and automotive equipment. Use these verified details to match this caster to carts and equipment that need swivel maneuverability, secure total locking, and floor-conscious rubber wheels in the specified application range.