Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
counter mount bearing plate kit gives installers a matched fastener set for counter mount elevated brackets with one fastening hole, so each bracket tightens down uniformly and supports countertop or workstation loads as designed. Branded as Federal Brace and classed under workstation and countertop brackets, this kit keeps hardware selection aligned with the original bracket engineering for predictable performance on finished counters. The galvanized finish on the components resists typical shop and jobsite environments, helping the bearing plates and threaded joints stay service-ready over time. Identified by manufacturer part number 39974, the kit makes it easy to specify the exact fastener solution the bracket manufacturer designed for its counter mount configuration. By pairing the right bearing plates, screws, and nuts with compatible elevated brackets, this kit helps crews install counters and work surfaces with repeatable clamp force and reduced rework on fastening details.
This Federal Brace counter mount bearing plate kit is described as a fastener kit for counter mount elevated brackets with one fastening hole, so each bracket is drawn tight through a single through-fastening point instead of multiple scattered fasteners. That single-hole design streamlines drilling, marking, and tightening on counters and worktops where access may be limited beneath the surface. Classified under workstation and countertop brackets, the kit aligns with mounting needs where the bracket must clamp firmly between the counter structure and supporting frame. The galvanized finish on the components supports dependable tightening torque by helping threads and bearing faces resist surface corrosion that could affect clamping over time. With manufacturer part 39974 clearly stated, installers can match the fastening approach across multiple brackets on the same run, keeping alignment and bearing pressure consistent from bracket to bracket.
This counter mount elevated bracket kit is tied directly to workstation and countertop bracket use, so it suits situations where a support bracket carries a counter, bar top, or workbench surface from beneath or behind. Because it is designed for counter mount elevated brackets with one fastening hole, it is most applicable where each bracket relies on a single hole through the structural member, such as a stud, ledger, or support frame behind the counter edge. On these jobs, the matched bearing plates and threaded components clamp the bracket body against the mounting surface, helping transfer the counter load efficiently into the underlying structure. The galvanized finish supports use in typical interior shop, office, or residential counter areas, where incidental moisture or handling could otherwise affect exposed fastener surfaces along the bracket mounting zone.
Because this is a dedicated counter mount bearing plate kit for elevated brackets with one fastening hole, installers gain a consistent fastening configuration from bracket to bracket, which supports uniform load distribution along a counter run. The single-hole fastening design means the installer focuses on one properly sized and located hole per bracket, which can improve drilling accuracy and reduce layout variation between supports. Being categorized as workstation and countertop bracket hardware, the kit is tailored to applications where a solid mechanical connection is critical for maintaining level counters under daily use. The galvanized finish on the components helps maintain thread engagement and bearing contact surfaces over time, so the clamping force applied during installation can continue to support the bracket. The Federal Brace manufacturer part number 39974 gives project documents and ordering systems a clear reference, promoting repeatable selections on multi-phase or multi-location countertop projects.
The counter mount bearing plate kit is designed for counter mount elevated brackets with one fastening hole, so it serves brackets that secure through a single through-hole into the supporting structure.
The Federal Brace kit is classified under workstation and countertop brackets, so it is intended for projects where brackets support counters, workstations, or similar horizontal surfaces in finished spaces.
The galvanized finish on the components provides corrosion resistance, helping the fasteners and bearing plates retain their functional surfaces in typical interior shop or residential counter environments.
Manufacturer part number 39974 identifies this specific counter mount bearing plate kit from Federal Brace, allowing straightforward specification, ordering, and reordering for matching installations.
The one fastening hole design means each bracket is secured through a single location, which simplifies drilling, alignment, and tightening steps along a counter or workstation installation.
The kit is described for workstation and countertop brackets, so its components support clamping elevated brackets that carry horizontal surfaces like counters, benches, or worktops.
The counter mount bearing plate kit from Federal Brace, identified as manufacturer part 39974, is built specifically for counter mount elevated brackets with one fastening hole, giving installers a consistent fastening approach across workstation and countertop projects. Its role within the workstation and countertop bracket class means the components support bracket connections that carry real working loads in counters and benches. The galvanized finish keeps working surfaces of the fasteners and bearing plates service-ready in normal interior environments. For projects relying on elevated counter mount brackets using a single through-hole connection, this dedicated bearing plate kit provides a focused way to align fastener selection with the bracket design.
