Cedan Walnut Wood Veneer Edgebanding 1 5/8", Unfinished, AEWALN158 500

American Veneer Walnut Edgebanding For Clean Edges

American Veneer Walnut Edgebanding gives cabinet and millwork projects a walnut edge that visually matches walnut wood surfaces, so face materials and edges read as a single, continuous walnut panel on finished work. The 1-5/8 inch width covers standard substrate thicknesses with room for trimming, which helps installers flush-trim cleanly without risking a short reveal along the edge. The fleece back construction on this wood edgebanding adds a backing layer behind the veneer, which supports the veneer during bonding so it stays more stable along the edge. This product is classified as wood edgebanding, so it serves as the visible finished edge on plywood, particleboard, or similar sheet goods where a real-wood walnut edge is required.

Key Walnut Edgebanding Details For Pros

• The American Veneer Walnut Edgebanding identity ties this product to walnut visual projects, so installers can select it when a walnut face and walnut edge are required on the same job.
• The 1-5/8 inch width specification provides extra coverage over common panel thicknesses, giving fabricators trimming tolerance that supports faster, more confident edge work at the bench.
• The fleece back construction behind the walnut veneer creates a backed edgeband, which helps the veneer sit uniformly on the substrate during pressing for a more consistent glue line.
• The wood edgebanding category definition means this product supplies a real wood walnut edge, supporting projects where exposed plywood or board edges need to present as solid walnut.
• The Cedan Inc brand identification connects the edgebanding to a known manufacturer, which helps shops keep part numbers and sourcing organized across repeat walnut edge jobs.

Walnut Edgeband Sizing For Straightforward Installation

The specified 1-5/8 inch width on this American Veneer Walnut Edgebanding gives installers working room when applying it to panel edges, so slight alignment variation still trims back to a full walnut face. As a wood edgebanding product with a fleece back, it is built to be bonded along exposed sheet-good edges, then trimmed and finished as part of normal edgebanding workflow. The fleece back construction reinforces the walnut veneer during the bonding and trimming steps, so the edge can be processed with typical edgebanding tools in shop or onsite settings.

Where Walnut Fleece Back Edgeband Works

Using American Veneer Walnut Edgebanding In Woodwork

American Veneer Walnut Edgebanding is positioned for woodworking projects where a walnut appearance is required at the panel edge, so cabinets, fixtures, or casework present a walnut look on both faces and edges. The wood edgebanding classification means this strip forms the exposed edge surface, allowing fabricators to take sheet goods and finish them to resemble walnut components. The 1-5/8 inch width is well suited to typical cabinet-grade sheet stock, giving enough overhang to trim flush along both sides while still keeping a full walnut band after machining. Because the product is identified specifically as walnut edgebanding, it is chosen for projects where walnut is the core design requirement across a run of parts.

Details That Support Consistent Edgeband Results

The fleece back construction on this walnut edgebanding adds a dedicated backing under the veneer, helping the strip conform evenly along panel edges for a more uniform bond line and reduced risk of veneer stress during handling. The American Veneer Walnut Edgebanding name sets expectations that the band visually coordinates with walnut-faced components, which simplifies layout decisions when running multiple walnut parts through the same job. The 1-5/8 inch width specification also streamlines setup, since shops can standardize trimming passes around that width and reuse the same approach on repeated walnut edge runs. The Cedan Inc brand and AEWALN158-500 manufacturer part number give shops a consistent reference for reorders, supporting repeatable results when matching previous walnut edge work on future projects.

Common Questions About This Walnut Edgeband

Select American Veneer Walnut Edgebanding With Confidence

American Veneer Walnut Edgebanding in 1-5/8 inch width gives woodworking shops a defined walnut edge solution that aligns with walnut-faced components across cabinets, fixtures, and casework. The combination of fleece back construction, wood edgebanding classification, and Cedan Inc manufacturer identification results in a clearly specified strip for walnut edge work. Selecting this AEWALN158-500 edgebanding allows projects using walnut-faced sheet goods to carry the same walnut look across every visible edge.