Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
3-15/16 nylon recessed pull black identifies this Hardware Concepts 2194-014 pull as a compact, recessed handle built around a 3-15/16 inch (100 mm) length, so it gives a defined gripping area while staying small enough for tight cabinet layouts. The black finish on the Nylon Series pull establishes a consistent, dark visual line along doors or drawers, which helps when matching other black decorative hardware in a run of cabinets. Nylon material defines the pull as a non-metal option, affecting how it feels in the hand and how it interacts with surrounding surfaces during repeated use. Recessed design is signaled directly in the description and indicates that the pull nests into a cutout rather than standing proud, which matters where a low profile is needed to limit catch points. The 2194-014 part number clearly ties this specific pull to the Nylon Series within the Hardware Concepts product class.
The web description specifies that two screws are needed for each pull, which sets the basic fastening pattern and influences how drill points are laid out on the cabinet face. The recommended screw is identified as #6 x 5/8 inch (Wurth Baer item WW41210), so installers can match thread size and length to the pull body when fastening into typical cabinet materials. Screws are stated as not provided, meaning that fasteners are selected from stock with this #6 x 5/8 inch guidance in mind. The 1/8 inch projection figure indicates that, once mounted, the pull stands off the surface only slightly, which matters when confirming clearance relative to nearby components while still allowing a finger grip at the recess.
The Hardware Concepts 3-15/16 inch length recessed pull, noted as part of the Nylon Series, is designed to sit into a recess on a cabinet door or drawer front, so the body occupies a routed or machined opening rather than hanging off the edge. The 2-1/32 inch width dimension defines how much vertical or horizontal panel area is devoted to the pull, guiding layout on narrow rails or stiles. Because projection is given as 1/8 inch, the front face of the pull interrupts nearby lines only slightly, which suits installations where doors slide past adjacent panels or where a low profile is preferred on utility or furniture pieces. Using two screws for each pull, as stated, naturally balances holding force at both ends of the 3-15/16 inch span, which supports alignment when the pull is operated repeatedly.
The stated length or diameter of 3-15/16 inch, paired with the 2-1/32 inch width, provides two key outer dimensions that allow jigs or templates to be built for repeat recessing across cabinet runs, which improves consistency between doors. The Nylon Series material designation tells installers they are working with nylon, which influences drilling pressure and handling when the screws clamp the pull against wood or composite substrates. The recommended #6 x 5/8 inch screw size, noted directly in the description, defines a common fastener combination that interacts predictably with the pull body and typical cabinet thicknesses. The SAP description and manufacturer part number 2194-014 both point back to the same recessed nylon pull specification, helping shops reorder the exact same component for future projects so replacement or expansion pieces match installed hardware dimensions and finish.
The Hardware Concepts 2194-014 recessed pull has a 3-15/16 inch length, 2-1/32 inch width, and 1/8 inch projection, so routing and drilling can be planned around these fixed measurements.
The 1/8 inch projection keeps the pull very close to the cabinet surface, which is helpful where doors operate near walls or adjacent components while still allowing access at the recess.
The pull is described as Nylon Series material nylon, so the handle body is nylon and interacts accordingly with tools, fasteners, and cabinet substrates during installation.
The web description recommends #6 x 5/8 inch screws, Wurth Baer item WW41210, giving a specific size and length to match the pull and typical cabinet construction.
The description states that two screws are needed for each pull, so fastening is provided at both ends of the 3-15/16 inch body for stable mounting.
The finish is specified as black, so the recessed pull presents a dark, uniform look that lines up visually with other black handles and pulls on the same project.
The Hardware Concepts, Inc. 3-15/16 inch length black recessed pull, listed as 2194-014 in the Nylon Series, offers defined dimensions, nylon construction, and a black finish that can be matched across jobs. With two-screw mounting and a recommended #6 x 5/8 inch fastener, the pull provides a clear fastening pattern for cabinet doors or drawers. When a low 1/8 inch projection and a 2-1/32 inch width fit the cabinet layout, this recessed nylon pull can be specified confidently as part of a coordinated handles and pulls hardware plan.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 100 Each |  WW41210 Mfr# 3670000004961 100 | Würth #6 x 5/8" Flat Head Hinge and Drawer Slide Installation Screw Phillips Drive - Sharp Point Coarse Thread Zinc, 3670000004961 100 - 100/Box |