Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Sugatsune SP Series recessed pull gives a low-profile way to open doors or panels using a 1-3/4 inch long stainless steel pull. The recessed style keeps the pull set into the surface, which helps reduce snag points in tight spaces. Satin stainless steel construction provides a hard-wearing metal gripping surface, useful where repeated hand contact is expected. The satin stainless steel finish reduces glare and fingerprints compared with bright mirror finishes, which helps the front stay visually consistent over daily use. A square 1-3/4 inch width matches the 1-3/4 inch length, creating a balanced, compact pull area that suits smaller doors or drawers. A 1/16 inch projection means the pull stands out very slightly from the mounting surface, which offers just enough edge for fingers while keeping the overall profile nearly flush.
The recommended mounting method for this Sugatsune SP Series recessed pull is 2 part epoxy glue, which bonds the pull to the prepared recess without through-bolts. Using 2 part epoxy glue as recommended creates a fixed connection between the stainless body and the substrate, which supports repeat opening and closing cycles. Because the pull is designed as a recessed style, the body nests into a cutout matching its 1-3/4 inch by 1-3/4 inch footprint, which helps resist lateral movement once the epoxy sets. The minimal 1/16 inch projection means the recess depth closely matches the pull body depth, so the front face sits nearly level with the surrounding surface after installation.
The Sugatsune SP Series 1-3/4 inch long recessed pull suits projects requiring a compact, square pull area in stainless steel. The 1-3/4 inch length and 1-3/4 inch width give a small but usable hand contact zone, which fits narrow cabinet doors, modest drawers, or sliding panels. Because the projection is only 1/16 inch, this pull serves well where hardware needs to sit almost flush, such as passage areas where people brush past fronts. The satin stainless steel finish coordinates with other satin stainless steel cabinet hardware, which helps maintain a uniform appearance across banks of doors and drawers. Stainless steel construction also means the same pull can be used across work areas and storage runs that share stainless hardware.
The SP-35/S manufacturer part number identifies this specific 1-3/4 inch square recessed pull in the Sugatsune SP Series, which helps repeat the same model wherever a matching pull is required. The defined 1-3/4 inch by 1-3/4 inch footprint allows consistent cutout sizing from cabinet to cabinet, supporting efficient fabrication. Using 2 part epoxy glue as the recommended mounting method ties installation to an adhesive-based process, which can speed work where rear access for bolts is limited. The 1/16 inch projection provides a clear target when setting recess depth so the pull face sits close to flush with the surrounding panel, which improves visual alignment across multiple fronts. Satin stainless steel across all visible surfaces creates a uniform tone, which simplifies coordination with other satin stainless hinges, pulls, or trim pieces in the same area.
The SP-35/S recessed pull has a length of 1-3/4 inches and a width of 1-3/4 inches, creating a square pull area that simplifies layout and routing for the recess.
The recessed pull has a projection of 1/16 inch, so it stands very slightly proud of the mounting surface while remaining effectively low profile in use.
The Sugatsune SP Series SP-35/S recessed pull is made from stainless steel, providing a metal body suitable for repeated handling on cabinet and furniture fronts.
The SP-35/S recessed pull has a satin stainless steel finish, giving a muted appearance that coordinates with other satin stainless cabinet hardware.
The stainless steel recessed pull is recommended to be mounted using 2 part epoxy glue, bonding the pull into its recess without relying on exposed fasteners.
The SP Series recessed pull suits cabinet, furniture, and panel projects needing a compact, square, satin stainless steel pull that remains nearly flush with the surface.
Sugatsune SP Series recessed pull offers a 1-3/4 inch by 1-3/4 inch stainless steel grip area with only 1/16 inch projection, fitting projects that call for a nearly flush stainless detail. The satin stainless steel finish aligns with other satin stainless hardware runs, helping maintain a clean, consistent appearance across an installation. With 2 part epoxy glue recommended as the mounting method, this pull matches workflows that favor adhesive-set recessed hardware. For cabinet, furniture, or panel work that benefits from low-profile stainless pulls, the SP-35/S recessed pull from Wurth Baer Supply fits that role with a defined size and finish.
Sold In: 1 Each
