Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Dynabrade replacement pad gives you a medium 5 inch hook and loop face that restores grip and contact on a compatible sander. The 5 inch size matches typical random orbital sander footprints, so the pad supports full-disc abrasive coverage without overhang that could mark work surfaces.
The pad design is identified as non-vacuum, so it is intended for sanders that do not use through-pad dust extraction, which suits simple air or electric tools on general woodworking jobs. A hook and loop face holds matching hook and loop abrasive discs, allowing fast disc changeover between grits while keeping discs flat on the pad.
The pad carries a maximum operating speed of 13,000 RPM, so it is built for sanders that run at that speed range in normal use. Working within this speed rating helps the pad maintain performance under sustained use during sanding passes on wood projects.
This Dynabrade 5 inch replacement pad uses a 5/16-24 male thread connection, so it attaches to sander spindles or pad mounts that accept that specific threaded interface. That threading style allows the pad to thread directly into the matching female thread on a compatible tool, creating a solid connection for sanding.
The non-vacuum style means there are no through-pad dust holes, so the full pad surface supports the abrasive disc. This uninterrupted face keeps contact concentrated on the disc and can help with consistent scratch patterns on flat wood panels, doors, or face frames during shop work.
The Dynabrade replacement pad is a 5 inch disc pad meant for use on sanders designed around that diameter, which are common in woodworking tasks such as smoothing cabinet parts, furniture components, and trim pieces. The hook and loop face pairs with matching hook and loop abrasive discs, allowing installers and woodworkers to cycle through coarse to fine grits while keeping discs centered.
Its non-vacuum design focuses on tools that do not route dust through the pad, which aligns with many compact sanders used around benches and jobsite setups. The medium pad construction serves as a practical middle ground between very hard and very soft pads, which helps it handle intermediate sanding on flat stock and gentle profiles where too-soft support might round edges.
The 5/16-24 male thread mounting allows the pad to engage directly with a sander that has that specific thread in its backing interface. This direct threaded connection supports stable pad rotation, which is important when working near edges or on narrow rails where wobble could mark the surface. With a maximum operating speed of 13,000 RPM, the pad matches many sanders that run at high speed for efficient stock removal, supporting steady work without the pad being pushed beyond its rated speed.
The combination of a 5 inch diameter and medium pad firmness helps operators repeat the same contact pattern across multiple parts, which is important for building runs of cabinet doors or case parts that sand out to a similar finish. The hook and loop interface keeps discs locked in place yet removable, which assists in maintaining consistent backing support even as different grit discs are changed during a finishing sequence.
The non-vacuum nature of the pad means no dust channels interrupt the pad face, so the abrasive disc is supported across its full area, which can help avoid localized pressure points when leveling putty, edge banding, or joints. The 5/16-24 male thread mounting detail ties the pad directly to tools built for that thread, helping preserve alignment and balance during operation at up to the stated 13,000 RPM maximum operating speed, which supports a smooth sanding feel during extended use on wood components.
This Dynabrade replacement pad is a 5 inch pad, so it is intended for use with 5 inch hook and loop sanding discs, providing full support across the disc surface.
The 5/16-24 male thread means the pad screws into a sander that has a 5/16-24 female thread, creating a direct mechanical connection for stable sanding.
Non-vacuum on this 5 inch pad means there are no dust extraction holes through the pad, so the full pad surface supports the hook and loop sanding disc.
This Dynabrade replacement pad has a maximum operating speed of 13,000 RPM, so it is suited to sanders that run within that speed range during use.
The product is identified as a medium pad, so it offers a mid-range support level that balances firmness with some conformity on wood surfaces.
This pad is described as hook and loop, so it is designed for hook and loop sanding discs that attach and release using the hook and loop interface.
Choose this Dynabrade replacement pad when a 5 inch medium non-vacuum pad with a 5/16-24 male thread is needed for sanding tasks. The hook and loop face works with hook and loop discs, supporting quick abrasive changes around the shop or jobsite.
The 13,000 RPM maximum operating speed aligns with many compact sanders, so the pad can serve in routine wood sanding work. Sourcing through Wurth Baer Supply connects this Dynabrade pad to a range of woodworking-focused products for shop operations.
Sold In: 1 Each
