Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Manor House bail pull gives cabinets a traditional American Federal look using a compact, functional handle layout. The zinc die cast construction forms a rigid base and hanging bail, so the pull delivers a solid gripping point on doors or drawers. The Lancaster hand polished finish creates a warm brass tone across the bail pull, which helps it visually match other Lancaster brass hardware in the same area. A 2-1/2 inch (64 mm) center to center dimension sets exact hole spacing, which matters when laying out new cabinet fronts or lining up with existing bores. The 3-1/2 inch overall width defines how much horizontal rail space the bail pull occupies on a face frame or panel. A 5/8 inch projection keeps the pull close to the surface, which is useful where doors pass near adjacent cabinetry or trim.
This bail pull is specified with a 2-1/2 inch (64 mm) center to center dimension, which sets the exact distance between mounting holes through the cabinet face. That spacing is important when replacing an older handle drilled on 64 mm centers or when setting up boring patterns on new work. The 3-1/2 inch width defines the overall footprint, which helps when checking that the bail pull stays inside rails and stiles without crowding edges. A 5/8 inch projection sets how far the bail sits off the surface, which affects both hand clearance and how closely doors can swing past framing. The stated 1-3/4 inch screw length or diameter value indicates the fastener specification for through-bolting the bail pull to typical cabinet fronts.
The American Federal collection reference in the web description places this bail pull in a traditional design family, which suits cabinets or furniture calling for a period-inspired hardware profile. The 2-1/2 inch (64 mm) center to center sizing makes this bail pull a match for layouts based on that common spacing, which is useful on many existing cabinet doors and drawers drilled to the same pattern. The 3-1/2 inch width means the pull fits comfortably on narrow rails or small drawer fronts without overpowering the face. Its 5/8 inch projection keeps the handle close to the cabinet plane, which helps in tight galley runs where doors open near side panels, appliances, or architectural trim. The Lancaster hand polished finish aligns the pull with other Lancaster brass elements in a room, which supports a consistent finish schedule on a multi-opening run of cabinets.
The specified 2-1/2 inch (64 mm) center to center dimension gives installers a fixed boring pattern, which streamlines jig setup for drilling multiple doors or drawer fronts with the same spacing. The zinc die cast material creates a uniform, precise casting for the bail and posts, which supports consistent alignment across a bank of fronts. The 3-1/2 inch width and 5/8 inch projection values define the installed envelope of the pull, which helps when planning clearances between adjacent fronts so handles do not interfere. The Lancaster hand polished brass finish is applied to the zinc die cast body, which produces a continuous appearance across every installed bail pull on a project. The 1-3/4 inch screw specification identifies the fastener length or diameter expected with this pull, which guides drilling depth through typical cabinet doors or drawer fronts to achieve secure mounting.
The bail pull has a 2-1/2 inch (64 mm) center to center dimension, which sets the exact hole spacing for mounting on cabinet doors or drawers.
The bail pull is 3-1/2 inches wide, which defines the horizontal space it occupies on the cabinet rail or drawer front.
The bail pull projects 5/8 inch from the cabinet surface, which keeps the profile low while still allowing fingers to grip the handle.
The P8048-LP bail pull is made from zinc die cast material, which provides a consistent base for the Lancaster hand polished finish.
This bail pull uses a Lancaster hand polished finish, giving it the specified brass appearance to coordinate with Lancaster brass hardware.
The bail pull lists a 1-3/4 inch length or diameter screw size, defining the fastener specification for mounting through typical cabinet fronts.
The P8048-LP bail pull from the Hickory Hardware Manor House Series combines a 2-1/2 inch (64 mm) center to center pattern with a Lancaster hand polished brass finish, so it supports both precise mounting and coordinated appearance. The zinc die cast construction, 3-1/2 inch width, and 5/8 inch projection define a compact footprint that works well across multiple cabinet and drawer sizes. For projects built around American Federal styling and Lancaster brass finishes, this bail pull provides a clearly defined set of dimensions and finish details to align the hardware layout.