Camar 806 Hanging Rail Bracket with White Cover Cap, 220 lb per pair Right Hand, Screw Mount,806-14-DX

Camar 806 Hanging Rail Bracket For Wall Systems

Camar 806 hanging rail bracket is a right sided bracket for wall hanging rail systems, giving installers a defined support point on the rail so cabinets or storage units hang in a controlled way. This bracket is used to hang on hanging rail part number CM875-Z1-24, so it ties directly into that rail profile for a matched system. The screw mount design lets the bracket fasten solidly to the cabinet side, which keeps the load path predictable when the cabinet is lifted onto the rail. A white cover cap finishes the visible portion of the bracket, so exposed areas around the cabinet top edge present a clean look in closets, wall units, or garage storage. As part of a wall hanging rail system, this bracket becomes the link between the cabinet carcass and the structural rail, helping the installation stay aligned over time.

Key Bracket Details That Support The Job

• The bracket is used to hang on hanging rail part number CM875-Z1-24, so installers can match the bracket directly to that specific rail and keep rail and bracket geometry consistent across multiple cabinets on the same run.
• A screw mount connection secures the bracket to the cabinet, so loads transfer through fastened points and the cabinet can be lifted onto the rail without the bracket shifting during handling or final alignment against the wall.
• The bracket has a weight capacity of 220 lb per pair, giving a defined load rating that helps plan cabinet size and contents within that range so the wall hanging rail system stays within its intended working capacity.
• The design offers 25 mm left and right adjustment, allowing the cabinet position on the rail to move laterally to fine tune reveals between cabinets and align doors or drawer fronts along a continuous wall run.
• Vertical adjustment of 28 mm up and down lets the cabinet height be tuned after hanging, so the installer can align cabinet bottoms or tops relative to reference lines and compensate for minor wall or floor irregularities.
• A white cover cap finishes the bracket, so any visible portion near the cabinet top or side aligns with light colored casework interiors and keeps the hardware appearance consistent in closets and storage applications.

Mounting And Adjustment For Rail Hung Cabinets

This Camar 806-14-DX bracket uses a screw mount, so it fastens to the cabinet side or structure using screws through the bracket body, tying the cabinet box into the wall hanging rail system. Once the cabinet is hung on the CM875-Z1-24 rail, the 25 mm left and right adjustment range lets the cabinet shift along the rail for reveal and joint tuning between adjacent units. The 28 mm up and down adjustment then lets the cabinet height be set relative to other cabinets or layout marks without removing the cabinet from the rail. Working with 220 lb per pair weight capacity helps plan cabinet sizing and loading so the bracket and rail are used within their stated capacity.

Using This Bracket In Wall Rail Installations

Where The Camar 806 Bracket Is Applied

This bracket is part of a wall hanging rail system in the Shelf, Closet & Garage Organization category, so it fits well in closet bracket and rail systems or wall mounted storage runs. As a right sided piece, it positions on the right side of a cabinet or unit, pairing with a corresponding left sided bracket to support the cabinet on the CM875-Z1-24 rail. The wall hanging rail system product class means the load transfers through the rail into the wall rather than through a floor base, which is useful for closet organizers or garage cabinets where floor clearance is preferred. Because it is used with the CM875-Z1-24 rail, the interface between bracket hook and rail profile is defined, helping cabinets hang consistently along the rail.

How Bracket Adjustments Support Clean Results

The 25 mm left and right adjustment built into this Camar 806-14-DX bracket lets an installer shift the cabinet laterally after it is hanging on the rail, so door gaps, end panel reveals, and joint lines between cabinets can be tuned without removing the unit. This is especially useful on long closet or wall runs where small shifts add up to a straight visual line. The 28 mm up and down adjustment gives additional control of height, letting the cabinet be raised or lowered relative to level marks or adjacent cabinets while it stays on the CM875-Z1-24 rail. Combined with the 220 lb per pair weight capacity, these adjustments support a workflow where the cabinet is first hung securely, then moved within the defined ranges to dial in final alignment. The white cover cap then keeps the adjusted bracket discreet in light interiors, supporting a finished appearance once all tuning is complete.

Common Questions About The Camar 806-14-DX Bracket

Selecting This Bracket For Rail Hung Cabinets

The Camar 806 hanging rail bracket with white cover cap, in right sided screw mount form, gives a defined way to hang cabinets on CM875-Z1-24 rails with 220 lb per pair capacity and measurable adjustment. For closet, wall cabinet, or garage storage layouts built around a wall hanging rail system, these specifics support planning cabinet positions, loads, and alignment. Selecting this 806-14-DX bracket when using CM875-Z1-24 rails ties the cabinet connection, adjustment travel, and appearance directly to the stated system components for repeatable installations.