Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Conquest 3 inch pull is a zinc die cast cabinet handle in the Conquest collection with a polished chrome finish. The 3 inch center to center drilling locates fasteners consistently across doors and drawers, which supports clean layout lines and repeatable boring setups in the shop. The 3-3/8 inch overall length gives a bit of overhang past the screw centers, giving fingers a clear edge to grab. A 7/8 inch projection brings the grip away from the cabinet face, which helps fingers clear raised panels and door profiles. The 3/4 inch width creates a stable hand contact area, which helps when heavier drawers are pulled open. The polished chrome finish reflects surrounding surfaces, which can visually tie together hinges and other bright chrome hardware on the same project.
The 3 inch center to center layout sets the drilling distance between fasteners, which lets installers use standard 3 inch boring jigs for accurate, repeatable hole placement. The 3-3/8 inch overall length keeps the ends close to the mounting holes, which matters when working on narrow drawer fronts or small doors where space is limited. The 7/8 inch projection sets the standoff from the face, which helps balance finger clearance with avoiding excessive protrusion into walkways. The 3/4 inch width defines the contact band on the cabinet surface, which distributes load as drawers are pulled. The 8-32 x 1 inch screw size provides a familiar machinist thread and length, which fits typical cabinet door and drawer front thicknesses used with this style of pull.
The polished chrome finish on this Conquest series pull suits projects that already use bright chrome hinges or decorative hardware, because the shared finish keeps the hardware set visually consistent. The 3 inch center to center measurement aligns with a widely used cabinet drilling standard, which helps when updating fronts that already have 3 inch holes or when setting up line-boring equipment for new runs. The 3-3/8 inch overall length fits comfortably on medium cabinet doors and typical drawer widths, which is useful in kitchens, bathrooms, and built-in casework where fronts are often sized around these ranges. The 7/8 inch projection gives enough stand-off for a comfortable finger grip on doors and drawers, which is practical on face frame and frameless cabinets with similar overlay conditions.
The zinc die cast construction creates a precise mounting geometry, which helps the pull seat flat when tightened against cabinet faces and reduces the chance of rocking on smooth finishes. The 3 inch center to center spacing allows installers to rely on existing jig holes and templates, which reduces layout time and keeps handle alignment consistent across long cabinet runs. The 3-3/8 inch length makes end clearances easy to measure from door edges and stile lines, which simplifies lining up multiple pulls on banks of drawers. The 3/4 inch width defines a compact footprint that still spreads load across the surface, which matters on thinner fronts or applied drawer panels. The 7/8 inch projection positions the gripping area away from door profiles, which helps hands clear raised or routed edges while opening. The 8-32 x 1 inch screw size connects this pull to a standard fastener pattern, which supports straightforward swap-out of other 8-32 threaded pulls in retrofit situations.
The P14441-26 pull has a 3 inch center to center, 3-3/8 inch length, 7/8 inch projection, and 3/4 inch width, which together define drilling layout, hand clearance, and surface footprint.
The 3 inch center to center spacing matches a common cabinet drilling standard, which works well with typical jigs and templates used for repetitive pull installations and replacements.
The pull is zinc die cast, which provides a uniform metal body that seats consistently against cabinet faces and supports precise alignment when the screws are tightened.
The P14441-26 pull has a polished chrome finish, which visually coordinates with other polished chrome cabinet hardware and trim on the same project.
The specified screw size is 8-32 x 1 inch, which matches common cabinet pull threads and works with many typical cabinet door and drawer front thicknesses.
This pull is part of the Conquest collection from Belwith Keeler under the Hickory Hardware name, which helps match it with other Conquest series pieces.
The Hickory Hardware Conquest 3 inch pull in polished chrome offers a zinc die cast body with a 3 inch center to center layout, which fits common cabinet boring patterns and replacement scenarios. Its 3-3/8 inch length, 7/8 inch projection, and 3/4 inch width define a compact, workable footprint for many doors and drawers. The 8-32 x 1 inch screw size ties this pull to a widely used cabinet hardware thread standard, aligning with many existing installations. For projects using polished chrome and 3 inch drill spacing, this Conquest series pull from Wurth Baer Supply provides a clearly defined option.
Sold In: 1 Each