Bisco P-14 aligning element gives you a 65mm x 27mm x 7mm biscuit-style connector that positions parts consistently, which helps keep cabinet components and panels flush during glue-up and assembly. The Lamello branding on the Bisco P-14 aligning element identifies it as part of a well-defined biscuit and fastener system, so it slots naturally into workflows that already rely on biscuit-style alignment. The 65mm length of this element bridges a decent span across a joint, which supports better registration between mating edges on longer seams or wider frames. Its 27mm height presents a generous bearing surface in the groove, which helps stabilize workpieces as you bring clamps on and off during the build. The 7mm thickness of the Bisco P-14 aligning element sets a predictable groove requirement, which simplifies tool setup and repeatable runs when cutting multiple joints.
The 65mm x 27mm x 7mm size of the Bisco P-14 aligning element defines the groove geometry you work around, so you can match cutter diameter and depth directly to those dimensions. The 65mm length dictates how far into each workpiece the biscuit seats, which affects where you lay out grooves in narrow rails versus wider panels. The 27mm height influences how close to an edge you cut, which matters when balancing holding power against the remaining material around the groove. The 7mm thickness establishes the clearance the element occupies, so you can tune cutting tooling and feed to achieve a snug, alignment-focused fit that still allows parts to pull together under clamp pressure.
The Lamello Bisco P-14 aligning element operates as a biscuit within the Fasteners | Dowels & Biscuits category, which positions it squarely for cabinetmaking and woodworking joints that rely on slotted connectors. Its 65mm length suits longer edge-to-edge seams on panels and carcase parts, giving you a stable bridge across the joint line. The 27mm height lets the biscuit sit securely within typical cabinet member widths, supporting alignment in rails, stiles, and shelf edges. With a 7mm thickness, the Bisco P-14 aligning element matches groove dimensions tuned to this profile, which is useful when standardizing a specific joint style across a run of similar components.
The defined 65mm x 27mm x 7mm size of the Bisco P-14 aligning element gives you a fixed reference for setting up joinery equipment, which supports repeatable cuts and less trial fitting. Knowing the exact length allows you to space biscuits along a seam in a predictable pattern, which spreads alignment support evenly and helps keep doors, fronts, or panels tracking flat. The 27mm height provides enough engagement in the groove to resist twisting under clamp load, which helps joints stay flush while adhesives set or while fasteners elsewhere are driven. The 7mm thickness means every groove cut for this element shares the same profile, which simplifies job planning when multiple team members are preparing parts for final assembly.
The Lamello Bisco P-14 aligning element functions as a biscuit-style connector that aligns mating wood parts, which supports flush joints in cabinet and woodworking assemblies.
The 65mm x 27mm x 7mm dimensions define groove length, height, and thickness, which guide where you position slots and how you size tooling for consistent alignment results.
The Bisco P-14 size spans a useful length for cabinet joints, giving enough engagement to stabilize wider panels and carcase parts during assembly and clamping.
The 7mm thickness sets a specific groove width target, allowing cutters to be dialed in so the aligning element seats snugly while still allowing the joint to pull tight.
Being in the biscuits class means the Bisco P-14 is designed to sit in opposing grooves, helping position parts relative to each other rather than acting as a surface fastener.
The Lamello brand identifies the Bisco P-14 as part of a recognized dowels and biscuits family, which supports consistent use alongside matching joinery methods.
The Lamello Bisco P-14 aligning element, at 65mm x 27mm x 7mm, offers a defined biscuit profile that supports precise cabinet and woodworking joints. The established biscuits classification and Lamello branding align this part with common dowel-and-biscuit workflows. The fixed dimensions give installers and shop teams a clear basis for tooling setup and joint layout on repeat projects. For work that depends on predictable alignment across rails, stiles, and panel seams, this Bisco P-14 aligning element provides a standardized connector size ready to drop into existing groove-based joining processes.
Sold In: 1 Box