Kitchen Kompact Glenwood base corner cabinet GW39BC is a 39 inch wide, 34-1/2 inch high, 24 inch deep base corner unit that turns a dead kitchen corner into usable cabinet storage. The solid 3/4 inch oak, maple, or beech frame gives this recessed panel cabinet a stable structure for everyday loading, so the box stays square during installation and over years of use. Each rail is kiln-dried, which stabilizes the wood before assembly and helps the frame resist seasonal movement that can throw doors and fronts out of alignment. The rails are joined by mortise and tenon and then glued, creating strong mechanical joints that keep the face frame rigid when the cabinet is fastened into a run. Solid wood corner blocks are glued and power nailed, tying the sides and frame together so the cabinet holds up under countertop and use loads in the corner position.
This Kitchen Kompact 39 inch wide, 34-1/2 inch high, 24 inch deep Glenwood base corner cabinet is sized for standard base runs, so it integrates into typical kitchen layouts without odd transitions. The solid wood hanging strips on the base cabinet at the top and bottom create defined fastening zones when you anchor the unit to studs or adjacent cabinets. Solid wood toe kicks at 3/4 inch thick let you scribe to floor variations while still keeping enough material for a solid finished edge. The 3 ply, 1/2 inch thick engineered wood core end panels with hardwood veneers provide flat sides for tight seams to neighboring cabinets, helping you maintain straight lines along the run.
The Kitchen Kompact Glenwood 39 inch base corner cabinet GW39BC is designed as a base corner unit in a Kitchen Kompact installation, so it fills the corner while tying straight runs together. With a 34-1/2 inch height and 24 inch depth, it aligns with standard base cabinet heights and depths, which simplifies planning for countertop depth and overhang. The solid 3/4 inch oak, maple, or beech frame at the front gives you a sturdy reference for aligning doors and drawer fronts in the surrounding cabinets. Solid wood corner blocks that are glued and power nailed tie the frame and sides together, giving the cabinet body strength when you fasten it to adjacent boxes on both sides of the corner. End panels built with 3 ply, 1/2 inch thick engineered wood core and hardwood veneers present stable surfaces that meet neighboring cabinets cleanly, which is important for creating a continuous appearance along both legs of the corner.
Construction on this Glenwood base corner cabinet centers on solid wood and engineered components that support repeatable jobsite results. Each face frame rail is kiln-dried, joined by mortise and tenon, and then glued, so the frame is less likely to open at the joints when you pull cabinets together with clamps or fasteners. That joint stability keeps reveal lines more consistent across the run. Solid wood hanging strips on base cabinets, located at the top and bottom, give you predictable fastening bands, which helps when laying out screw positions along studs or into adjacent cabinets. The solid 3/4 inch toe kicks provide enough material to trim or scribe to irregular floors while keeping a firm foundation against the subfloor. The 3 ply engineered wood end panels with hardwood veneers resist warping, which helps maintain cabinet squareness and reduces time spent adjusting neighboring units to compensate for side bow or twist.
The Kitchen Kompact Glenwood base corner cabinet GW39BC is 39 inches wide, 34-1/2 inches high, and 24 inches deep, so it aligns with common base cabinet and countertop layouts.
The frame is built of solid 3/4 inch oak, maple, or beech, with each rail kiln-dried, joined by mortise and tenon, and glued, giving a rigid front that supports alignment and fastening.
The solid wood corner blocks are glued and power nailed, tying cabinet sides and frame together so the box better handles loads from countertops and daily kitchen use.
The solid wood toe kicks are 3/4 inch thick, providing a strong lower front that tolerates foot contact and allows scribing to uneven floors while keeping structural strength.
The solid wood hanging strips at the top and bottom of the base cabinet give consistent fastening areas, helping achieve a secure mount into studs or adjoining cabinets.
The end panels use 3 ply construction with a 1/2 inch thick engineered wood core and hardwood veneers, providing flat, stable sides that finish cleanly and meet adjacent units.
The Kitchen Kompact Glenwood 39 inch base corner cabinet GW39BC combines a solid 3/4 inch wood frame, kiln-dried mortise and tenon rails, and 3 ply engineered end panels to support a stable corner in your layout. Solid wood corner blocks, toe kicks, and hanging strips give defined structural points for fastening, trimming, and aligning neighboring cabinets. For a base corner position that ties two runs together using Kitchen Kompact construction details, this unit offers a job-focused option.
Sold In: 1 Each