Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Classic Series oven cabinet gives you a 33 inch wide by 96 inch high Wolf Dartmouth Brownstone unit designed for built-in oven layouts where consistent case dimensions matter across a run of tall cabinets. The two butt doors on this cabinet organize the upper section so face-frame access lines up cleanly with adjacent storage, which helps keep vertical reveals consistent. Three bottom drawers create a base-style storage zone under the oven opening, giving you a defined area for heavier items without needing a separate base cabinet. Cabinet fronts are made from 3/4 inch solid maple wood, providing a hard, stable face frame and door material that holds up well when doors and drawers are used repeatedly. Rails are pocket drilled and assembled with 1-1/4 inch screws for rugged durability, so the front frame resists racking when the tall cabinet is anchored into a wall run.
Half-depth adjustable shelf of 3/4 inch plywood with bull-nosed, foil-covered front edges gives you a stout support surface that does not extend full depth, leaving space behind for utility runs while keeping the front edge protected. The shelves are held in place with self-locking 1/4 inch diameter clips on the sides, which means vertical adjustment happens at the case sides and the shelf stays positively engaged once set. This approach helps keep the shelf level under normal loading without relying on friction alone. In a 96 inch high oven cabinet, that adjustability is useful for aligning interior storage above or below the oven cutout so front reveals and usable heights can be tuned to the appliance and surrounding cabinets.
This Wolf Home Products tall unit is a Classic Series oven cabinet built at 33 inches wide and 96 inches high, which suits kitchen runs where a full-height oven tower is planned alongside matching tall pantries. The two butt doors at the upper section give access to the tall cavity above the oven space, so trays or lighter items can be stored without needing an extra wall cabinet. Three bottom drawers provide base-height storage at floor level within the same footprint, which is useful in layouts where floor space is limited but separated drawer storage is still needed. Side panels and bottom in 1/2 inch plywood with matching exterior laminate allow this cabinet to present a finished side when exposed at the end of a run, so the oven unit can terminate a bank of cabinets without additional finishing steps. Back panels in vinyl-covered 1/2 inch plywood create an interior surface that pairs a smooth back with structural thickness, supporting the height of the overall case.
Cabinet fronts made from 3/4 inch solid maple wood give the face frame and doors a dense material that holds screw fastenings for hinges and drawer fronts, which helps hardware stay tight during repeated opening cycles. Rails that are pocket drilled and assembled with 1-1/4 inch screws provide a positive mechanical connection at each frame joint, helping the tall frame stay square against wall studs when the oven cabinet is fastened in place. Side and bottom panels glued and stapled into a 1/2 inch dado in the cabinet front frame add a tongue-and-groove style engagement, which resists separation forces as the loaded cabinet is anchored. Back panels glued and nailed in a 1/2 inch dado and stapled to the hang rail and cabinet bottom create a closed box that distributes loads between top, bottom, and sides when the oven weight is carried. All-wood 3/4 inch corner blocks at every corner strengthen those joints, supporting the cabinet when drawers are extended and the interior is fully loaded. The half-depth adjustable 3/4 inch plywood shelf with bull-nosed, foil-covered front edge offers a front edge that stands up to contact with stored items, while the half-depth design keeps rear space open for clearances. Self-locking 1/4 inch diameter clips holding the shelf at the sides give a positive register in each hole, which helps maintain shelf position while the tall cabinet experiences day-to-day use.
This Classic Series oven cabinet is 33 inches wide by 96 inches high, so it fits tall runs where a full-height oven tower is planned.
The cabinet fronts are 3/4 inch solid maple wood, while the side panels, bottom, and back use 1/2 inch plywood for a stable case.
The rails are pocket drilled and assembled with 1-1/4 inch screws, creating strong frame joints that support the tall cabinet structure.
The half-depth 3/4 inch plywood shelf is supported by self-locking 1/4 inch diameter clips on the sides, giving positive support at the chosen height.
The cabinet has a toekick that is 4-1/2 inches high by 4-1/16 inches deep, providing a recessed base area at the floor line.
The vinyl-covered 1/2 inch plywood back panels are glued and nailed in a 1/2 inch dado and stapled to the hang rail and bottom to brace the case.
Choose this Wolf Home Products Classic Series oven cabinet when you need a 33 inch wide by 96 inch high Dartmouth Brownstone unit that ties into tall kitchen runs. The combination of 3/4 inch solid maple fronts, 1/2 inch plywood case construction, and all-wood 3/4 inch corner blocks gives you a structural cabinet ready to function as an oven tower. With two butt doors, three bottom drawers, a half-depth adjustable shelf, and a 4-1/2 inch high by 4-1/16 inch deep toekick, this cabinet organizes oven placement and surrounding storage within a single tall footprint.
Sold In: 1 Each