Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Sugatsune Fastmount low profile clip describes this LP-AF8A female clip as a low profile panel mounting fitting, so it sits close to the surface and helps keep panel build-ups tight where space is limited. The clip is part of the Sugatsune Fastmount Series panel mounting system, so it works as one component within a repeatable panel assembly workflow for finish panels. It is a female clip with auto fit lateral adjustment for use with curved panels, so it can take up small side-to-side differences where panels do not sit perfectly straight. The clip mounts into a 1 3/8 inch, or 35 mm, pre-drilled hole in the substrate, so installers can use a standard size bore to prepare the base material. It fits into plywood, MDF, fiberglass, and similar substrates, so it supports a range of common panel materials on jobs. The minimum panel thickness is 7/16 inch, or 10.5 mm, so it is suited to medium-thickness panels used in many interior projects.
The LP-AF8A low profile female clip mounts into a 1 3/8 inch pre-drilled hole in the substrate, so drilling a 35 mm diameter hole sets the pocket for each clip location. The clip is affixed with #6 countersunk screws, or M3.5 equivalents, which allows use of standard countersunk fasteners often stocked in shops and on site. The minimum panel thickness for this clip is 7/16 inch, or 10.5 mm, so installers can plan material selection and edge treatments around that requirement when designing panel sets. The clip fits into plywood, MDF, and fiberglass, so a single fastening method can be carried across different panel materials within a room or fixture. As part of a Fasteners and Panel Mounting Systems category, this panel assembly fitting supports a hardware-based approach to panel installation.
The LP-AF8A low profile female clip is identified as a panel mounting fitting within the Fasteners and Panel Mounting Systems category, so it is intended for attaching removable or finish panels to a prepared substrate. It fits into panel materials such as plywood, MDF, and fiberglass, so installers can apply the same clip approach to cabinetry surrounds, decorative wall treatments, or similar panel-based assemblies using those materials. The clip is designed to mount into a 1 3/8 inch, or 35 mm, pre-drilled hole in the substrate, so the receiving structure needs that bore wherever a panel connection is required. With a minimum panel thickness of 7/16 inch, or 10.5 mm, the clip suits medium-thickness panels common in interior woodworking and fit-out work. As a female clip within the Sugatsune Fastmount Series, it is used together with compatible male clips to create a two-part connection between panel and substrate.
The LP-AF8A female clip provides auto fit lateral adjustment for use with curved panels, so slight misalignment across a run of curved or irregular surfaces can be absorbed by the clip rather than transferring into visible panel steps. This lateral adjustment helps panels sit more evenly against the substrate, which reduces rework from re-drilling or slotting mounting points. Because the clip is low profile, the assembled panel stack uses less depth, which can be valuable behind casework, in tight recesses, or wherever services run directly behind the panel. Using a 1 3/8 inch, or 35 mm, pre-drilled hole as the mounting interface lets installers repeat the same drilling pattern across multiple clips, supporting consistent spacing and faster layout. Affixing the clip with #6, or M3.5, countersunk screws ties installation to a familiar screw format, so drivers and bits already in use on site can carry through this step. The specified minimum panel thickness of 7/16 inch, or 10.5 mm, gives a clear threshold for panel selection, which supports planning around weight, stiffness, and edge detailing in design and fabrication.
The LP-AF8A is a Sugatsune Fastmount Series low profile female clip classified as a panel assembly fitting, so it serves as part of a fastening system for mounting panels to a substrate.
The LP-AF8A clip provides auto fit lateral adjustment for use with curved panels, so it can take up small side-to-side variations and improve alignment on non-straight surfaces.
The LP-AF8A clip fits into plywood, MDF, fiberglass, and similar substrates, so it can be used across different panel materials in the same installation.
The LP-AF8A female clip is specified for panels 7/16 inch, or 10.5 mm, thick or greater, so it suits medium-thickness panels often used in interior work.
The LP-AF8A clip mounts into a 1 3/8 inch, or 35 mm, pre-drilled hole in the substrate and is affixed using #6, or M3.5, countersunk screws.
The LP-AF8A female clip is compatible with male clips LP-M8A and LP-SM8A, so it pairs with those parts to form a complete Fastmount connection.
The LP-AF8A low profile female clip from Sugatsune America combines auto fit lateral adjustment for use with curved panels, a 1 3/8 inch pre-drilled hole interface, and #6 countersunk screw fixation. Those details support efficient, repeatable mounting of plywood, MDF, or fiberglass panels when a minimum panel thickness of 7/16 inch is part of the design. For panel assembly fittings within a Fastmount-style system, this LP-AF8A female clip provides a defined role in securing finish panels to a prepared substrate.
Sold In: 1 Each