HandiSOLUTIONS division molding is designed to hide the seam between two HandiWALL slatwall panels, so adjoining panels present a single continuous surface. By covering the joint, this molding gives finished HandiWALL runs a cleaner, more professional appearance wherever two panels meet.
This division molding is made of extruded PVC, which forms a consistent profile along its length for predictable fit against HandiWALL panels. The extruded PVC construction supports straightforward trimming on site, so installers can cut pieces to match panel layouts and wall conditions.
The molding is specified at 80' length in black, giving installers a long run to service multiple seams or longer panel runs while maintaining the same dark trim color along the entire installation. The black color coordinates with black HandiWALL panels or creates a dark accent line when used alongside other HandiWALL finishes.
The product is made in the USA, which provides a consistent manufacturing source and supports repeatability when the same division molding is needed across multiple projects or phases.
This division molding is designed to hide the seam between two HandiWALL slatwall panels, so it is used wherever separate panels meet along a run. By bridging those joints, the molding visually unifies adjacent panels and reduces the appearance of panel breaks.
The extruded PVC construction supports cutting the molding to length on site, so installers can size pieces precisely to the seam locations created by their HandiWALL layout. Because the product is specified as black, it establishes a defined dark line at the seam, either blending with black panels or creating a deliberate contrasting trim at panel joints.
The 80' length provides ample material from a single product for use across several seams on the same project, simplifying selection when standardizing division molding on larger HandiWALL wall systems.
This HandiSOLUTIONS division molding is designed for use specifically between two HandiWALL slatwall panels, so it fits into projects where HandiWALL panels are installed side by side. Whenever a run of HandiWALL creates a visible joint line between adjacent panels, this molding is applied at that joint to conceal the seam.
The product belongs to the Slatwall & Accessories class and the Shelf, Closet & Garage Organization category, aligning it with storage and organization layouts that rely on HandiWALL slatwall surfaces. That makes it suitable for closet, garage, or similar spaces built around HandiWALL panels, where a clean transition between panels supports a more finished wall appearance.
Because the molding is supplied as an 80' length in black, it suits larger HandiWALL setups that require repeated seam coverage along extended walls. Installers can pull sections from the same continuous length, helping maintain consistent visual lines across multiple seams in the same room or project.
The molding is made of extruded PVC, which delivers a continuous, uniform profile that stays consistent along the full 80' length. This uniformity helps installers rely on the same cross-section at every cut, so each piece behaves the same way over HandiWALL panel seams.
Extruded PVC also responds well to typical cutting approaches used with PVC trim, so installers can size sections precisely to match seam locations without changing tooling between different slatwall finishing components. This supports efficient on-site fitting as panel layouts change from wall to wall.
The 80' length offers extended linear footage from a single product, reducing the number of separate division molding references required on jobs with multiple HandiWALL seams. That length lets installers handle long continuous runs or many shorter seams while keeping the same HST4080D profile and black color throughout the installation.
The black finish of this division molding creates a defined line where two HandiWALL slatwall panels meet, which either blends with black panels or acts as a deliberate dark trim when panels use another finish. This color consistency supports repeatable visual outcomes across closets, garages, or other storage areas outfitted with HandiWALL panels.
The HandiSOLUTIONS division molding is designed to hide the seam between two HandiWALL slatwall panels, so joint lines are concealed and finished HandiWALL runs appear more continuous.
The 80' length in black gives extended linear footage from one product, allowing installers to cover multiple HandiWALL panel seams or longer runs while keeping a consistent molding profile and color.
The HST4080D division molding is made of extruded PVC, which provides a uniform profile along its length and supports straightforward cutting to fit specific HandiWALL seam locations.
This division molding is made in the USA, supporting consistent sourcing and repeatability when the same HandiSOLUTIONS HST4080D profile is used across multiple HandiWALL installations.
The molding is designed to hide the seam between two HandiWALL slatwall panels, so it covers the joint and helps the wall surface read as a more continuous HandiWALL installation.
The HandiSOLUTIONS HST4080D division molding is specified as black, providing a dark trim line at HandiWALL seams that can blend with black panels or contrast other panel finishes.
The HandiSOLUTIONS division molding, HST4080D, is designed to hide the seam between two HandiWALL slatwall panels, giving finished walls a more continuous appearance. Its extruded PVC construction and 80' black length support consistent results across HandiWALL installations in closet, garage, and other organization projects.
Sold In: 1 Each