Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Sugatsune SP Series recessed pull is a 2-1/4 in (57 mm) square stainless steel pull that sits recessed into the surface, creating a low-profile grip that supports clean, flat cabinet or panel fronts. The pull is made from 304 stainless steel, so the metal resists everyday corrosion and staining in typical woodworking and cabinet environments. The satin finish diffuses light on the 57 mm square face, helping panels and doors read as a uniform surface instead of drawing strong reflections to the hardware. This pull is part of the Sugatsune SP Series and carries the SP-48/S manufacturer part number, giving installers a clear reference when matching existing pulls on a job. The square form factor works wherever a compact, recessed handhold is preferred, helping doors, drawers, or access panels open without protruding hardware.
The 2-1/4 in (57 mm) square dimension of the Sugatsune SP Series recessed pull defines both the visible face size and the footprint that must be allowed in the panel, so installers can plan consistent reveals and spacing on cabinet runs. Because the pull is recessed, the body installs into a prepared cavity rather than sitting proud, which influences how deep a mortise or pocket is cut in doors or drawers. Using 304 stainless steel for the SP-48/S body gives a stable material around the recess edges, which supports crisp transitions between the pull and the surrounding surface. The satin finish on the square face works well when aligning multiple pulls, because slight shifts in light do not emphasize minor layout variations across a run.
The Sugatsune SP Series 2-1/4 in (57 mm) square stainless steel recessed pull fits projects that call for a compact handhold set fully into the surface, such as cabinet fronts, sliding panels, or furniture doors where projection must stay minimal. The 57 mm square footprint provides enough area for a practical finger grip while remaining small enough to integrate into narrow stiles or thin drawer fronts. With 304 stainless steel as the base material, this SP-48/S pull suits typical woodworking installations where metal needs to withstand routine contact without rapid surface breakdown. The satin stainless finish on the square face plays well with contemporary decorative hardware and moldings, letting the pull sit visually quiet alongside other Sugatsune hardware pieces on the same installation.
The SP-48/S manufacturer part number clearly identifies this specific 57 mm square recessed pull, which helps fabricators repeat the same component across multiple cabinets, casework runs, or replacement orders. Using a defined 2-1/4 in (57 mm) square outline gives CNC programmers and bench installers a fixed dimension for the recess, improving repeatability from shop setup through field fitting. The 304 stainless steel construction ensures the pull body matches common stainless tooling expectations, which supports clean edges at the transition between the pull and finished panels. Because the pull is part of the Sugatsune SP Series, installers can align this item with other SP series pieces when a project requires consistent hardware language. The satin finish further helps reduce visible misalignment between units, since softer reflections highlight the panel surface more than the pull itself, supporting a uniform look across a bank of fronts.
The Sugatsune SP Series 2-1/4 in (57 mm) square stainless steel recessed pull has a 57 mm square face, which sets the layout size for the recess and the visible hardware on the panel.
The SP-48/S recessed pull is made from 304 stainless steel, so the body resists everyday corrosion in typical cabinet environments and maintains a stable interface with the surrounding surface.
The Sugatsune SP Series SP-48/S recessed pull has a satin finish, which softens reflections on the 57 mm square face and supports a more understated appearance on doors and drawers.
The SP-48/S recessed pull sits into a cavity instead of projecting, so cabinet or panel fronts stay flatter, which helps when a clean, low-profile surface is required on the job.
The manufacturer part number SP-48/S identifies this specific 57 mm square recessed pull, helping projects match existing Sugatsune SP Series hardware during installs or later replacements.
The Sugatsune SP Series 2-1/4 in (57 mm) square stainless steel recessed pull suits cabinet, furniture, and panel applications that need a compact, recessed handhold without protruding hardware.
The Sugatsune SP Series 2-1/4 in (57 mm) square stainless steel recessed pull gives installers a clearly defined 57 mm square footprint, a 304 stainless body, and a satin finish, all tied to the SP-48/S part number. That combination supports consistent cutouts, straightforward specification, and a low-profile look across cabinetry, furniture, or panel work. For projects that call for recessed pulls from a defined decorative hardware and moldings line, this Sugatsune stainless recessed pull from Wurth Baer Supply offers a precise, repeatable choice for your next run of fronts.